Search results

  1. clement

    Best Combination

    if you are gonna run the stock intake there is NO, I repeat, NO reason to put heads on it. if you are gonna run most of the intakes on the market it really wont matter what heads you run because the intake will be the restriction. unless you run a TFS R or holley systemax 2. if I were going to...
  2. clement

    10 Sec 331 Help

    Mark at Bullet Cams.
  3. clement

    10 Sec 331 Help

    the rhs heads are great. my 215s with a VJ went 6.40s@101 in the 1/8th on top of a 347 on the motor. as far as the 331, no reason it shouldnt go 1o.90s on motor with the right supporting hardware. my buddies stock windsor shortblock at 10.0:1 compression, a flat tappet cam, a 750, and 1971...
  4. clement

    Good Ol Holley Double Pumper Tunning

    all those darn stock holley double pumpers do that. my recommendation would be to call AED and ask them which secondary metering parts you need to get it to stop.
  5. clement

    10 Sec 331 Help

    more gear, more converter, a trans brake wouldnt hurt, more compression. what heads, intake, cam, exhaust and suspension? the 28" tire with a 3.73 is like running a 3.55 with a 26.
  6. clement

    90s roller engine going in my 64 mustang

    well if a 38 will fit a 9mm should too! :D
  7. clement

    Aluminum or cast iron flywheel

    thats how my mcleod was.
  8. clement

    help with carburetor choice

    AED 650 HO. you will not believe the difference. depending on how mild the cam is it might work great with a 750 HO, which is also mech secondary. there is too much to this stuff to go into in a single post, but it is not about the cfm rating. its venturi size and metering, carb signal from the...
  9. clement

    Aluminum or cast iron flywheel

    ive never tested an aluminum flywheel vs. a steel one. however, I have freshened an engine and went from steel rods to aluminum rods saving almost 400g per hole between the lighter pistons, lighter rods and some very light wrist pins. then the weight savings from pulling mass out of the crank to...
  10. clement

    Pushrod question

    you can shim the pedestals to make up for that little bit of difference. no need for different pushrods with pedestal rockers unless something changes.
  11. clement

    90s roller engine going in my 64 mustang

    yes, swap them.
  12. clement

    DISCOURAGED! Should I replace, keep or give her up???

    my first was my 65 c code coupe. that car wasnt very nice to me so i sold it. i dont regret it. then i had a 91 lx 5 liter that i beat on, a guy went through a redlight and totaled it. i didnt care about that one either. however, my '93 GT has been in the family since new. i blew up the stock...
  13. clement

    90s roller engine going in my 64 mustang

    the 90s flexplate is a 50oz balance 164t. the early stuff was 28 oz 157t in the small bell c4s. so what you need is a 50oz balance with the same tooth count as the '70, which happens to be 157t. they are everywhere. try summit. 50 oz 157 tooth.
  14. clement

    90s roller engine going in my 64 mustang

    if it has the correct valvetrain it will be fine. when you increase lobe area or cross section you lower airspeed in the port if everything else remains constant. the smaller/lower flowing port needs lobe area more than a large port does on a given cylinder to support a given rpm. its all...
  15. clement

    65 mustang with a post 1970 289

    ford discontinued the 289 in 1968 in the U.S.
  16. clement

    help with carburetor choice

    if it goes dead lean with one carb and not another it isnt a timing issue. the thing i hate about holleys (even the HP series) is that the metering is never right. we ran a good 650 HP, a new 750 HP and a good 830 DP on a 351w with cleveland heads. it was fat on the secondary side with all of...
  17. clement

    help with carburetor choice

    http://www.aedperformance.com/ get rid of the holleys and get a real carb. you can play with a/f and changing jets/bleeds and even messing with metering and never get it right. I have seen cars pick up .4 in the 1/8 mile bolting on AED and other custom carbs over tuned stock HP holleys that...
  18. clement

    dipstick problem

    exactly, a dipstick will only read correctly if it in the sump.
  19. clement

    help with carburetor choice

    AED 650 HO
  20. clement

    Which Rockers Should I Get?

    IMO if you arent gonna race it and you are going to stick with pedestal mount and not go up to 1.7 ratio, i would spend the $ else where.
Top Bottom
Back
Forums
Menu