Search results

  1. 67coupestang

    89 Intermittent power loss pleases help

    wel... that wasnt it. Tach works though :) for the first 3 miles of the test drive after swapping modules, it was fine, then about a block from home it acted up again.. i dont know where else to look and its getting steadily worse. last night it was actually bucking like it was stalling out...
  2. 67coupestang

    89 Intermittent power loss pleases help

    Thank you! nobody could lead me in any direction at the ranger station... I'll see if i can pick one up tonight, or at least get one ordered, ill post results as soon as i find out. thanks a TON!
  3. 67coupestang

    89 Intermittent power loss pleases help

    ok its actually in my ranger but i seem to have the ranger station stumped... so heres the skinny ive had this ranger for about a year. got it cheap cause it didnt run, no biggie all it needed was a fuel pump, did that, cleaned out the tank, new filter, FPR etc. okay so fuel delivery...
  4. 67coupestang

    T5 jumps out of second gear

    i vote for the shifter boot binding... it happened to mine. the only reason it happens under decceleration is because under power the gears will kind of pull together like mentioned pull the boot off and even check clearances around the shifter hole before you panic and tear into the...
  5. 67coupestang

    stumbly 351w please help

    well the motor has maybe 6k on it it doesnt burn oil, it smokes only when it seeps on to the headers then its a mess. my pcv is connected to the front port on my edelbrock drivers side holds the valve then the rear of the passenger side has the vent. I picked up a mighty vac so i could do...
  6. 67coupestang

    stumbly 351w please help

    any thoughts on the oil geyser? its only rapid acclereration not only high rpm. im going ot pick up a vacucm guage after work today and see what i can find out. whats the best way to check the vacuum advance? maybe if i can find a vacuum pump/guage i'll pick that up
  7. 67coupestang

    stumbly 351w please help

    i searched and didnt come up with much, maybe i dont know how to phrase it. my 67 has a MAJOR stumble when the thottle is bipped hard off idle. i'm pretty sure its a vacuum leak but i cant find it. Its been on going for a while. ive replaced the carb base gaskets and the intake gaskets at...
  8. 67coupestang

    Sound Deadening Rocker Covers ?

    I Wonder if you could paint them with something? Like a truck bed liner, although i dont know about the temps... but like previously mentioned are you sure you're not masking some other problem?
  9. 67coupestang

    my speedometer cable keeps breaking...

    more than likely it has too sharp of a bend or its too close to something hot. i dont think they recomend lubing them, but i've been wrong before. the bobbing tells me that it was working harder than it had to
  10. 67coupestang

    My $2000 Ignition - I need help!

    ?? did you check spark while cranking? i had a bronco for a while that checked out fine, 12v at the coil while sitting, but dropped when the engine was cranking causing ignition failure and a no fire. for a while i ran the coil off a relay tied directly to the battery, later i found that a...
  11. 67coupestang

    Need Carb tuning 101 class

    ??? im not an expert but the edel's are adjustable. the accel shot is limited there are only 3 holes of adjustment... the secondaries, you have to change out the springs on either side of the air inlet. they dont control how fast the secondary plate opens, thats done on vacuum alone, but...
  12. 67coupestang

    Convertible seat riser in a Fastback

    how much differnce is there in the floors between a vert and fb/cp? comparing the pictures it just looks like there is a little trimmed off the back by th tq boxes. I ask because on my 67fb the rockers need to be replaced so i was considering the vert style to replace them with the one piece...
  13. 67coupestang

    Help me ID this 9" housing and maybe talk me out of it.

    i thought that too for a minute, but it looks like Reen's axle is sprung under.
  14. 67coupestang

    I HATE previous owners and body filler!

    better than the rivets i found hiding under 1/2" thick bondo :rolleyes:
  15. 67coupestang

    Hood scope

    a heat valve vac motor will work as well and they're usually smaller than most headlight ones i've seen
  16. 67coupestang

    top loader in south central Minnesota

    4 speed
  17. 67coupestang

    top loader in south central Minnesota

    no idea what to ask for it really just make me an offer. I need $$ for steel so i can get my fastback rolling :)
  18. 67coupestang

    top loader in south central Minnesota

    I have a toploader out of my fastback i dont think i'll need. Its from a 67 and the tag reads rug-E1. the gears look in great shape, just the one syncro looks a little worn 1-2 maybe? shifter is there but one of the tabs for the reverse lockout is broken off. I also have the bellhousing. she...
  19. 67coupestang

    69 block worth anything??

    sell nothing, all they have to do is pick it up :D whats that for odds now? 1:150 million?
  20. 67coupestang

    dynacorn question, not debate :)

    the floors are the same i belive minus a little trimming for the vert, but the seat base is a one piece that goes over the tranny hump instead of two seperate pieces in the coupe and fastback. I'm ignorant in not knowing what the difference in the rockers is? I'd assume stiffness, thats a...
Top Bottom
Back
Forums
Menu