Search results

  1. Grn92LX

    LMR coil over kit

    I went with MM coil over conversion kit with Tokico D spec struts and UPR 12-150 springs. Rides fine.
  2. Grn92LX

    Came Across This: Holley Efi Terminator X for your Fox Body Mustang

    You may find a dealer on any of the Holley Facebook groups that may save a few bucks but holley does not offer any discounts. Holleydays is a gimmick, just a higher 'suggested retail' price then their normal price.
  3. Grn92LX

    Digital Tuning Anybody running a Holley efi Pro dash?

    The Holley efi kit and pro dash wasn't hard to install. The coil and fuel pump need to be wired up but its pretty simple. I made a small relay panel hidden under the seat where the ecu is as well with the supplied bracket. You will need the can to usb cable to make tuning easier and to set the...
  4. Grn92LX

    Got the Anderson Top End Kit Installed

    I was thinking about using an air saw or maybe a jig saw with a metal blade. Or even drilling small holes around it and using an air saw to finish. I also ordered the anderson maf delete kit with 10" filter. My car is Holley efi so no maf.
  5. Grn92LX

    Got the Anderson Top End Kit Installed

    Is that a 4" power pipe? If so what did you use to cleanly cut the hole? Also, did it come with the seal for the hole? I just ordered one.
  6. Grn92LX

    Tuning advice

    Stock ecu with a moates quarter horse. You can hook up with a remote tuner for a few hundred bucks to dial it all in.
  7. Grn92LX

    Engine How to check for lower intake vacuum leak at lifter valley?

    How do you test and/or check for a lower intake vacuum leak at the lifter valley? Thanks
  8. Grn92LX

    Electrical Jumping alternator dash wire after digital dash install?

    I just realized after installing the digital dash with the 500ohm resistor jumper wire that I used a 1/4watt and not a 1/2 watt. I am starting to notice a sight voltage drop as I get into the higher rpms and also noticed slightly less voltage at idle. It used to be around 14.6 @ idle and now...
  9. Grn92LX

    HEY, is this 89' distributor supposed to do this?

    A cardone remanufactured distributer w/o module and w/o cap/rotor Is $70. I just replaced my original one that was very wobbly with it. It had a ford pick up still in it and I put a motorcraft tfi on it.
  10. Grn92LX

    Engine Cardone Distributor Cardone me wrong :(

    I just installed a cardone remanufactured distributer in along with a motorcraft tfi. It had a ford pick up still in it, they only change what’s bad in a reman unit so I got lucky. My stock distributer was wobbly as hell and it’s much easier to buy a reman then rebuilt it you’re not going to...
  11. Grn92LX

    Engine 90 Mustang engine swap - starts and stalls

    Engine needs more start up enrichment fuel, its too lean in the cold temps. Only way to fix it is with a tuning device ( chip, holley efi, megasquirt ect.)
  12. Grn92LX

    Electrical Jumping alternator dash wire after digital dash install?

    I got it from amazon. Came in a 100 pack for $6, needed 1 now I have 99 left. View: https://www.amazon.com/Projects-100EP512470R-470-Resistors-Pack/dp/B0185FIDF0/ref=sr_1_3?crid=3M74Y75N8VPOQ&dchild=1&keywords=500+ohm+1%2F2w+resistor&qid=1611081560&sprefix=1%2F2w+500+ohm%2Caps%2C185&sr=8-3
  13. Grn92LX

    Electrical Jumping alternator dash wire after digital dash install?

    Everything worked like a charm, thanks. How hot does a 1/2w 470ohm resistor get? I put a wire covering over the entire jumper I made so it won't touch anything. Is that ok?
  14. Grn92LX

    Megasquirt Digital Dash

    Anyone have pictures of how they jumped the alternator 12v with pins 2 and 14? Im doing a holley dash right now but the alternator jumper part is the same. Thanks
  15. Grn92LX

    Electrical Jumping alternator dash wire after digital dash install?

    Thanks, got the resistor ordered. Now what would be the best way to do this without cutting the factory wiring? Would a T tap connector on each wire with the resistor soldered in between work ok? T tap-jumper wire-resistor-jumper wire to T tap ? Or does anyone make a plug and play harness?
  16. Grn92LX

    Electrical Jumping alternator dash wire after digital dash install?

    Just looking for verification. Im in the middle of installing my Holley efi 6.86" pro dash. I know I need to jump the wires on pin 2 and 14 on the factory harness to turn on the alternator. Can I just run a simple 14g wire jumper or does it need a resistor soldered in? If so does anyone know...
  17. Grn92LX

    Digital Tuning Anybody running a Holley efi Pro dash?

    Anyone using one? Im about to start installing mine. Wondering about the alternator 12v wire, how to hook it up and if it needs a diode? thanks
  18. Grn92LX

    Digital Tuning Anybody running a Holley efi Pro dash?

    Thinking about getting one for my car. Already running holley terminator x. How do you like it? What did you do for the battery gauge alternator 12v signal wire?
  19. Grn92LX

    Engine Start up issue M. Car won't idle without throttle

    In the laptop software you need to set up the ford iac motor. Set it to pwm- and go into the pin map and drag/drop it to output 4. You can't do it on the handheld. Once thats done warm the car up, set the idle screw and do a tps autoset.
  20. Grn92LX

    Pulling the trigger on Holley terminator x.

    I have no problems with the factory tfi distributer. Only thing I had to do was bend the pins on the holley tfi adapter harness with a flat head. Its a common issue/easy fix. You already have the ignition box so the dual sync is only another few hundred bucks, up to you.
Top Bottom
Back
Forums
Menu