Search results

  1. 7

    ?Maverick steering box work on 69 stang

    Thanks stanger53,I checked out your site,Lots of info that I never new about steering boxes.Ill check out my steering box again and see if itsanything that can be adjusted. 75 mustang II
  2. 7

    ?Maverick steering box work on 69 stang

    yeloxr7 thanks,Checked out the link to Borgeson.Better price than some Ive looked at.Before I order Ill check the maverick a little closer ,for slop in the steering box.It was hit hard in the back and has under 60,000 miles on it.Its worth a shot.I noticed it had the same power assist as the 69...
  3. 7

    ?Maverick steering box work on 69 stang

    Got the new suspension kit from CJ pony.Was trying to adjust my steering box,real sloppy.If I keep going on the front end can the steering box be removed once the 351 is installed?Its in a 69 stang.
  4. 7

    ?Maverick steering box work on 69 stang

    Are there any other steering gear boxes that will interchange with a 69 stang.? I remember the maverick I pulled the spindles for front disc brakes.Looked the same.75 mustang II
  5. 7

    Engine block ID

    I pulled a valve pan cover and there is a big T stamped ..The casting # was 8E27.Its got the front sump pan,and the motor mounts are for a 69 mustang.It looks like it will drop in.The tranny mount is even the same.75 mustang II
  6. 7

    Engine block ID

    Thanks D. Hearne,I pulled the starter and these are the numbersE9AE-6015-AA-11 under that was 9J14.The tranny numbers tell anything? 75 mustang II
  7. 7

    Engine block ID

    Got these numbers off the exhaust mainifolds.D50E-9431-86 r manifold. left manifold D50E-9430-CA Got these off the tranny C6AP-7D027-C It has the performer 351 windsor intake and edelbrok carb. Was told the tranny was a c-4. Any info on any of these numbers would be great. Thanks
  8. 7

    Engine block ID

    Bought a 351 windsor with tranny that a guy pulled from a 69 mustang.Was trying to figure out what this motor was out of.The guy didnt know any history on the motor.Its complete even got the radiator.Its painted new softplugs and gaskets.Anyway of telling without tearing it down?
  9. 7

    76 maverick spindles on a 69?

    Havack,Glad to hear the parts are reasonable and still available.Not sure if the rims I have will be a problem or not.Need to fix the wifes van ,the kids bike tire,and the four wheeler.etc
  10. 7

    76 maverick spindles on a 69?

    65 Shelbyclone,We must of been typing at the same time.Im in northwest P.A and the yards around here are preaty good.They all tell you the same thing If they would have known years ago,they would have saved alot of the muscle cars.There is a maverick there that was a factory 302 auto on the...
  11. 7

    76 maverick spindles on a 69?

    Havack,Thanks for the replie.I bought the setup and will start changing over in a couple days.How do you like the setup on your 66?The car Im getting them from is a manual disc setup.I did a manual disc swap on my 69 charger and it stops great. 75 mustangII
  12. 7

    76 maverick spindles on a 69?

    Was at the recking yard ,looking for a granada for disc brakes on my 69.The guy that owns the place said that Mavericks were the same.After checking one out the maverick is a 5 bolt and it looks like the ball joints are the same.From what I could tell it looks like it will bolt on.Anyone ever...
  13. 7

    So I'm preping for Por-15... got a question

    Looks like your ready .Apply a thin coat and allow to dry then apply a second you shouldnt have any problems.Never used por filler but have heard its good stuff.Ive got por 15 that dripped on my garage floor over 5 years ago and doubt it will ever come loose.
  14. 7

    Heater noise, yes I searched

    Just a guess but its probably air trapped in it.
  15. 7

    What weld sealer?

    What I do is probably overkill but Ive never had any problems.When Im finished welding and cleanup the welds,I por 15 the welded area only.When possible front and back of welds.Let it dry for 24hrs and mix up duraglass and and apply thin coat of it both sides.Duraglass is water proof when set...
  16. 7

    Oil on dipstick always too high.

    Not sure on the oil capacity,seems like 5 quarts should be correct.On the valve pan covers it sounds like they may have been overtightened.What you could do is pull them off and check them with a straight edge.If you see alot of high and low spots thats the problem.You could try to straighten...
  17. 7

    Front windshield channel repair

    Had some rusted out areas in windshield channel.Ive cut out the bad and welded in new metal.I need some of the studs that hold the molding clips.Anybody know where a guy might find some?I think I need 5.
  18. 7

    Rust project

    Ive used the por 15 for rust .Eastwood is about the same.The encapsalator is made to go directly on to rust.Follow the directions on the drying time.As far as the brush just use the natural bristle brushes.They usually have some that are cheap throw away brushes.Dont know about eastwood but if...
  19. 7

    69 coupe emergency brake cable

    Ive finished installing new tourque boxes in my 69 coupe.The old tourque boxes were homemade and they had a whole blown in them for the emergency brake cable.My question is does the cable go down thru the floor or does it go out thru the firewall and back thru the tourqe boxes?There are wholes...
  20. 7

    Heads and intake numbers

    Thanks again.D.Hearne You have a good point.I havent heard how much for the motor parts yet.If the price is right Ill buy all and decide later what to do with the intake.What application would this intake be good for?
Top Bottom
Back
Forums
Menu