Search results

  1. Nicoleb3x3

    distributor shaft lenghts

    not sure about measuring from the gear down..but maybe the clip depth measurements might help you a bit: (note; this was based off retaining clip install hight issues...this may not give your enough info)
  2. Nicoleb3x3

    TB and Cold Air Intake Choking Engine?

    If you want recommendations on products...I like my set up: but it's NOT CHEAP anderson powerpipe...filter in the fender 70mm tb (bbk) although I intend on going bigger with a blower next year Adaco performance DBX97 90mm MAF *this is programmable and digital :) and can be any orientation...
  3. Nicoleb3x3

    No Crank Over- No Fuel Pump

    fuel pump I can't help...mine is not wired like stock.. but anyways...make sure the trigger wire on your starer relay is all the way on...make sure the big wire going to the starter on the relay is tight....this is the one on the terminal by itself on the relay. then make sure the two wires...
  4. Nicoleb3x3

    bucking problem

    how bad is it? mine did it a little bit like only a few slight bucks...this is after changing to a 5.0 it seemed like the drivetrain going front to back a little ...then it somehow got better and never did it again after a while...I also re-did my engine again recently and I don't have the...
  5. Nicoleb3x3

    which intake tube for 70 mm TB?

    I did the anderson powerpipe which adapts to multip tb sizes :) I have a 70 mm tb at the momment
  6. Nicoleb3x3

    1993 Mustang Headlight harness

    I 90% beleive I had to change the headlight harness because the alternator was part of that harness and it's going to be located on the other side of the car :) Dash harness WORKS AS IS...however; IF YOUR FUEL PUMP DOESN'T TURN ON YOU MAY NEED TO DO WHAT I DID: Originally Posted by MrKwik...
  7. Nicoleb3x3

    question about ring orientation

  8. Nicoleb3x3

    question about ring orientation

    I did mine over the winter, and I have perfect circle brand rings that came with these instructions that I used: "A" is the Oil Ring Spacer Opening (position not used) "B" is the Oil Ring Rail Gaps -*more like 11 oclock close to the left side "B" should be bottom oil ring gap...
  9. Nicoleb3x3

    cooling question?

    just curious if you changed your temp gauge lately? is it new?
  10. Nicoleb3x3

    timing question?

    Spring next year is my KB tiime frame, I need a full season to make sure my recently built engine is healthy and strong. I'll send you a pm
  11. Nicoleb3x3

    MSD 6AL worth it?

    I just had my stang on the dyno saturday and found out I need a msd box...my tuner who I trust said don't waste your money on the -2 version. I have afr 165 heads and putting on a Kb next year....so if I don't need the -2 and it's a waste of money for me...then perhaps you're wasting your...
  12. Nicoleb3x3

    Noisy Hydraulic Lifters - Any Fix Ideas ?

    I have an XE (266hr) comp cam also :)
  13. Nicoleb3x3

    Noisy Hydraulic Lifters - Any Fix Ideas ?

    mine make noise too...and I re-adjusted them also i don't have allot of miles on my engine yet, but if you wanted to have this for reference: YouTube - noise in brand new engine...5.0 93 mustang -video 3; noise fixed these are 1.7 trickflow roller rockers
  14. Nicoleb3x3

    timing question?

    cool your going with KB blower, I'm putting one on my stang next spring...feel free to book mark my site if you want to check it out when it's done, it'll be a poster child install for sure :) If you want some reference videos for noise, see below: Very bad loose rocker...luckily I only...
  15. Nicoleb3x3

    cooling question?

    I have the same thing happening....runs hotter than it did with the clutch fan ....I also have been running it all the time because I'm not used to it running as hot as this...but it's not "too hot" I have 180 thermostat, and high flow water pump, same as before my rebuild. but now I have...
  16. Nicoleb3x3

    I'm in the September issue of 5.0 Mustang & Super Fords magazine!

    congrats :)
  17. Nicoleb3x3

    The newbie Again.... should i get nitrous?

    If your stang is a daily driver I would suggest a blower over nitrious...otherwise you'll be filling that tank all the damn time
  18. Nicoleb3x3

    My overhaul on 4nomore- built by a girl :)

    I was in modified mustangs a few years ago yes :) And yes, I've done a few passes at NED and ran stock (but w/ exhaust and shift kit in the aod) at 14.67 ......I think it was last year. I will go this year if I can get the 8.8 rear put in soon and the engine is running good.
  19. Nicoleb3x3

    My overhaul on 4nomore- built by a girl :)

    Adding a few pics from today, inlcudes a complete engine shot (no missing stuff) and my maiden voyage today of 16 feet outside the garage (had to fix fan, a loose starter relay trigger wire and a few dripping tranny lines)
  20. Nicoleb3x3

    My overhaul on 4nomore- built by a girl :)

    It was bored .30 over and the crank is under .1 (stock crank) and stock block; but everything else is new
Top Bottom
Back
Forums
Menu