Search results

  1. ScratchinFerTra

    Fuel pressure gauge

    Like everyone else said, mounting a mechanical fuel pressure gauge in this manner is asking to be burned alive. If you are going to do it, do it right: http://store.summitracing.com/partdetail.asp?autofilter=1&part=ATM%2D5282&N=700+400442+115&autoview=sku This will connect to the line in...
  2. ScratchinFerTra

    Rolling fender lips?

    I asked the local fab shop what they charge to do this, and if they have the tool. They told me they do not roll fenders because you will have distortion in most cases. What they do and have done for many years is cut the majority of the lip off with a cut-off wheel, then a little paint on the...
  3. ScratchinFerTra

    Quick question/need opinions....

  4. ScratchinFerTra

    Help Diagnose my low rwhp issue. Any experts?

    As long as the valves don't float, the springs should not be too soft. Might want to call a cam expert to give what your cam specs are and what they would recommend for your set-up. My thought would be too little lift/duration to fill the cylinders, but that is just a stab in the dark. Stan
  5. ScratchinFerTra

    tko 500 swap

    Edit to my earlier post, the T5 and TKO I think are different bellhousings. I installed my TKO600 with a quicktime bell, and it is listed for T5, TKO 500/600, but I forgot it has a few tranny bolt patterns. Stan
  6. ScratchinFerTra

    tko 500 swap

    Foxbody T5 bell housing.
  7. ScratchinFerTra

    Tremec....

    Tremec site http://www.ttcautomotive.com/English/home/home.asp TKO parts list http://www.ttcautomotive.com/English/onlineorder/pdf/TRAP0090107_145.pdf Modern Driveline (very helpful group, if they answer) http://www.moderndriveline.com/ Keisler Engineering (helpful in forums)...
  8. ScratchinFerTra

    ABS compatability

    Tell me where they unplug up inside the car and I will send you mine, changing rears and getting rid of them, so for now they are in the way. Stan
  9. ScratchinFerTra

    Safest Jackstand Practice on 1990 Mustang

    Some ideas that might help. Just put a TKO in and about to install the 9". With doing the 5 lug convert up front you may want to go a different route than me, or maybe do one end at a time. Stan
  10. ScratchinFerTra

    Intake oil return pops out!

    The PCV has a check valve, but they are not 100% sealing, especially not under boost. The reason for the PCV is to incorporate the check valve to prevent backfires from the 1:1,000,000 chance they would cause a boom in the crankcase/upper block cavity. Stan
  11. ScratchinFerTra

    May have solved Braided Fuel line problem!

    Fuel systems seem to be the hot ticket right now, doing the same here. The two fittings from Summit, are for newer Mustangs and LS1s. The list a 5/16 and 3/8, but we need a 1/4" and 5/16", so use the 5/16 for the feed line, the return we are still SOL. The other three links: Steeda...
  12. ScratchinFerTra

    Does anybody know these bolt sizes.

    The smog pump bolts should be 3/8-16, not sure the length. Stan
  13. ScratchinFerTra

    Found oil puddled on timing cover (pics)

    Not sure the size, my old one broke into three when I took it off, I just ordered one from Ford.
  14. ScratchinFerTra

    rear shocks

    I had a similar issue last year. One was the right shock, the other too wide, I took it back and had them find me the right one. If you want to save some change, come to Vineland next week and I will give you my one year old ones, standard Advance Auto version, going coil-overs. Stan
  15. ScratchinFerTra

    Found oil puddled on timing cover (pics)

    Yellow94, Check around the distributor, there is an o-ring that seals the distributor that gets pretty hard over time, I once had blow by making oil come out there, a new o-ring stopped that. But the oil did lay on tip the water pump like yours. Stan
  16. ScratchinFerTra

    Clutch Cable Length

    To second the last comment, I just tonight installed a Steeda adjustable kit on my 95, the kit came with a Fox cable (60 inches) and the 95 cable is also 60 inches. Stan
  17. ScratchinFerTra

    9" Housing Ends with 96 GT Disk Brakes?

    There are all types of 9" ends out there. Mark Williams does an 8.8 upgrade that allows the use of stock brakes, ABS and all. Strange has 9" Mustang bolt-in retrofit rears that require there SVO brake kit or similar. The only rear difference is making sure the caliper mount bracket on the...
  18. ScratchinFerTra

    rear end

    Stange axle should.
  19. ScratchinFerTra

    Brother may have totalled my 98 cobra

    Was the rear narrowed at all, or just built?
  20. ScratchinFerTra

    Alternator Hits VC

    I was able to grind the round part of the back of the alternator that hit my Ford Racing tall valve covers on my 95Gt, all stock front engine components. Stan
Top Bottom
Back
Forums
Menu