Search results

  1. ponyboy19

    Fuel system for 347 N/A

    Gss340 pump, Kirban regulator, 30lb injectors while N/A if it was me.
  2. ponyboy19

    fuel system ques.

    Yes
  3. ponyboy19

    Guys with dumps

    I just ordered THESE and cut to length and welded..
  4. ponyboy19

    Jet-Hot coated intake?

    I jet hot coated my Vic Jr intake. Matches the polished elbow and parts perfectly. Only thing you have to do is sand it down smooth before you coat it or it will be gray since it doesn't shine until they make it shine after coating it. You can't buff and polish inside the pits of cast...
  5. ponyboy19

    Which injectors?

    If you want to spend some cash, buy a set of 24's and matching MAF. If you want to be cheap, pick up a used set of stockers off ebay and run the 19's for 30-40 bucks.
  6. ponyboy19

    Anyone running a Procharger Non i/c P1SC

    I ran a P1 non intercooled on an old 302 combo. made decent power but my advise is if your not going to go with an intercooler then use a vortech. My P1 at the same boost level as a freinds V2 s-trim had a lot hotter intake charge. So I don't think the p1 is nearly as effiecent. I heard the...
  7. ponyboy19

    fuel system ques.

    The Gss340 will be fine. If you step up to a power adder chances are your lines and rails will be the restriction.
  8. ponyboy19

    351 swapped

    my 418 with a Vic Jr Spyder sitting on an AJE K member and HPM extream duty solid mounts with spacers to raise the engine back up clears my 2.5" cobra R hood. But that's my set up and you didnt' mention what intake your using.
  9. ponyboy19

    104 octane

    If your set up and state of tune doesn't require it, then wouldn't run it.
  10. ponyboy19

    Which c/c plates to buy?

    the wheels and rear control arms won't matter in the front end alignment. But if you need new struts, tie rod ends, ball joints, or any other front end suspension part, it may be a good time to R&R it while it's apart.
  11. ponyboy19

    Optima Battery worth it?

    was yours hot for a long time like mine was when it spewed all over..
  12. ponyboy19

    Which c/c plates to buy?

    just follow the instructions.. it's not that hard. Get an alignment when you get them on.
  13. ponyboy19

    Which c/c plates to buy?

    I bought mine from here. http://www.corral.net/forums/showthread.php?t=676955 I can't remember the price, but I know it was one heck of a deal... Either way like anything else, you get what you pay for.
  14. ponyboy19

    Optima Battery worth it?

    I've sworn off Optima Red tops forever. The one I have in my 95 works great, but two out of three where junk. One blew up for no reason spewing acid all over my battery box in the trunk. Was smoking hot for a day or two sitting on the ground. The other one was dead when I got it, so I...
  15. ponyboy19

    Which c/c plates to buy?

    Get the Maximum Motorsports ones. They are top notch IMO.
  16. ponyboy19

    Will these Valve covers work with EFI?

    I don't think so with a standard EFI intake.. But I could be wrong. They look like FMS tall covers. When I had my edelbrock, TFS standard height covers were all I could get to fit, and I think I might have needed a 3/8 spacer. Can't remember. With a tall enough spacer and the hood clearance...
  17. ponyboy19

    Educate me on Rear Axles

    Personally I'm not a fan of Moser, I've seen of too many guys breaking them. If I were you, and assuming your car is primarily street, I would go with an Auburn Pro or Eaton 31 spline differential, differential cover, along with a set of Strange 31 spline S/S axles. I've heard guys running C...
  18. ponyboy19

    budget aluminum heads

    http://www.tristatecylinderhead.com/catalog/
  19. ponyboy19

    drivetrain clunk

    I think they all have it.. Even my race prepped spooled rearend will make some noise once and a while if I take off real easy.
  20. ponyboy19

    Electric Fan with Toggle Switch

    Don't do this. You need a relay in the middle of the toggle switch. The toggle should only be used to activate the relay which in turn operates the fan. Your running a fan not a night light. I've tried wiring things that pulled some power like stated above and have always burn toggles out...
Top Bottom
Back
Forums
Menu