Search results

  1. ozanracing

    Check out this CAI I made....

    There we go. Helps keep the heat out. I ordered a C&L trueflow tube also. I did'nt like the stock one's inside ridges.
  2. ozanracing

    Underdrive pulleys...convince me that they work.

    Nobody else cought this BS?? Come on! (WHAT IS THE JOB OF THE HARMONIC BALANCER?) Seriusly guys... :nono:
  3. ozanracing

    Check out this CAI I made....

    Haha the plug wires will be one color...The intake and valve covers arn't even bolted on right now. I'm installing my ISKY adj. guideplates...Plus I got new injectors (30lb/hr) coming to me by tuesday so I'll be putting them on also. Ya, I do want to clean things...But I'm feeling kinda...
  4. ozanracing

    New exhaust setup.

    Just taking pics....
  5. ozanracing

    Check out this CAI I made....

    Well I'll find out if it helps or hurts. It's a vortech maf, with stock electronics... Now all I need to make is a "heat shield"
  6. ozanracing

    Check out this CAI I made....

  7. ozanracing

    Check out this CAI I made....

    Here's the BBK kit: $160+ shipping. Seems like the same design, no? My theory is the filter mounted directly to the maf will create trubulance. So adding the pipe before it will "unify the air" before it hits the sensor.
  8. ozanracing

    Check out this CAI I made....

    It's a zex kit with the fuel control box "thing". That's the recomended place for the nozzle. After the MAF. I'll take some pics next time I go back to my shop of the "ram air" deal.
  9. ozanracing

    runs like a raped ape for 15 mins

    Sounds like the TFI going bad. :shrug:
  10. ozanracing

    Summit stage 2 intake manifold

    Link please
  11. ozanracing

    Check out this CAI I made....

    No; dry...
  12. ozanracing

    First run on spray

    H/C/I with n20....mmmmm.....Now All I need is a stroker bottem end-dart block. Then I'll be stoaked....for a bit....
  13. ozanracing

    Advice, $800 to spend

    I stand by my first post.
  14. ozanracing

    Check out this CAI I made....

    I had the filter mounted directly to the vortech 73mm maf, bu I beleave it may have been causing turbulance, and an incorrect sample. So I fabbed up this setup. The filter is compleatly in the fender, and where the turn signal was I made a duct and scoop that channels air right to the filter...
  15. ozanracing

    Advice, $800 to spend

    Gt40 heads used, tfs 1 cam, used cobra intake. DUH.
  16. ozanracing

    E7TE or E6SE

    You are not smart if you just slap a cam in without checking piston to valve clearance. Especially with a e6 block. The e7 heads are worth 25hp over the e6 heads.
  17. ozanracing

    Two questions on TrickFlow install instructions

    You remove the retaining clip from the top of the lifter, then take out the plunger and spring. Go get some #10 washers, and stack them up inside the lifter...Then re assemble it with just the plunger and retaining clip. It's now going to act "solid". (as in it won't depress.) The preload of...
  18. ozanracing

    Phenolic spacer inbetween the upper/lower intake manifolds???

    Mine keeps the upper much cooler than without it. it's the trickflow 3/8" one.
  19. ozanracing

    Cheap headers any good? Flowtech 1 5/8" longtubes for $125...

    Summit sells long tubes for like $96. Fit/work great. look into those.
  20. ozanracing

    Block dowels

    Trickflow sells them for a few dollars.
Top Bottom
Back
Forums
Menu