Search results

  1. 67FBack

    67 Super Snake Project

    I used Russell Black AN 8 supply line and Russell Black AN 6 return line. Two 45's coming out of the tank: You can barely see the Aeromotive 10 micron fuel filter that I added with 2 90's: Then I run all the lines and battery cable to the front: I used a lot of clamps to...
  2. 67FBack

    67 Super Snake Project

    I completed the front and rear brake line and master cylinder. I went to our local O'Reilly Auto Parts and used their free double flaring tool. I needed three reducers from the Baer Brakes to the Ford lines (2 front, 1 rear). This is the rear: I also needed two straight connectors...
  3. 67FBack

    67 Super Snake Project

    I installed the battery box and mounted it to the frame to comply with NHRA rules. I also cut through the bottom of the battery box, insulated the holes and run the cables out the bottom of the box so you cannot see any wires. The protective covering has been left in place for now.
  4. 67FBack

    67 Super Snake Project

    Here is some picture of the front lights installed without the upper nose:
  5. 67FBack

    67 Super Snake Project

    The new locking gas cap.
  6. 67FBack

    67 Super Snake Project

    And I have completed 90% of the Painless Wiring 14 circuit system for the Mustang. I am pleased with the kit. Very easy. I just wished it had more than 1 extra relay. I will use it for the electric windows. I will have to add 6 extra circuits for the high amp items like High Beams, Low Beams...
  7. 67FBack

    67 Super Snake Project

    When I got about 95% done with the Old Air A/C. Very straight forward and good quality, but I am not impressed with the vents.
  8. 67FBack

    67 Super Snake Project

    Installing the rear lights need a lot of attention and time. I mounted the studs to the rings with loctite red. Made sure everything fits right. Lenses go in from the inside. I had to cut some more of the tail panel. But it looks good. Cant see it from this picture though. I installed the...
  9. 67FBack

    67 Super Snake Project

    Here is a couple of shots of the rear valence panel with the factory light housing mounted. They have been ground out to accept the rear PIAA BU lights.
  10. 67FBack

    67 Super Snake Project

    Putting the car back together after the undercoating. I have got many thing accomplished. Installed the exhaust system. Putting the exhaust through the rear torque boxes is a challenge. It took me 1 1/2 days to finish. Muffler is only tacked on inlet side at this point. With a...
  11. 67FBack

    67 Super Snake Project

    I dropped the front and rear running gear, and prepared the entire car for undercoating. I shot the underside with 2 coats of Lizard Skin Sound Control and 2 coats of Lizard Skin Ceramic Heat Insulation. This stuff is pretty thick and should work well. However, I did not like the ending...
  12. 67FBack

    67 Super Snake Project

    I plunged head first into what I thought would be something difficult. Turns out the decision was the difficult part. I laid out the fuel filler pipes. While helpful, there is no clear point to install it. So I tried to find a place that the filler tube would fit without cutting the...
  13. 67FBack

    67 Super Snake Project

    Installed the upper rear scoops. Ground down to metal for the bonding agent. Taped it off and painted the fins and inside scoops gloss black. Removed the tape. Ground off the paint around the edges and trimmed it a little. Squeezed out the bonding agent and...
  14. 67FBack

    67 Super Snake Project

    After I got everything installed, I set in it and , lock to lock is only 2 turns!!!! That is good, however the turning radius sure looks like it could be tighter: Get Er Done
  15. 67FBack

    67 Super Snake Project

    Got the steering wheel installed. Then I had to play a little. (See , I got it up to 4000rpm! hah) Couldn't resist. I didn't mount the instruments, though.
  16. 67FBack

    67 Super Snake Project

    I installed the Flaming River steering column. This is the new lower plate that hold the column at the firewall. The tabs get bent in, and are used to hold the column. Mounted the knuckles to the R&P and the column. I marked and drilled the intermediate shaft for setscrew indent...
  17. 67FBack

    67 Super Snake Project

    Progress? Well here is 3 months worth of progress... I installed the headlight buckets in the upper nose, and installed the front fender brace. I had to remove this small bracket Put the headlight in the bucket G] And 5885 epoxy glued it in place
  18. 67FBack

    The Reenmachine DOHC '67 Shelby Clone Convertible Progress

    Sound Control I also used the Lizard Skin Ceramic Insulation and the Sound Control Formula. (PS. got a $140 gun for sale at half price) and am wondering if I should use the mat, also. Let us know. I got your E-Mail about the console window switches. Thanks! Gonna be at SEMA in Vegas? Gonna...
  19. 67FBack

    Wanted: 68 Fastback Trunk Hinges

    I am looking for a set of 68 Fastback Trunk Lid Hinges. I do not want the 67 hinges. They use the torsion spring which can warp fiberglass. Thanks
  20. 67FBack

    Shelby A-arm Relocation and Lowering Questions

    20's on a stang remind me of this: :jaw: Just MHO.
Top Bottom
Back
Forums
Menu