Search results

  1. 873Stang

    dowel pins in flywheel pics???

    i agree changed mine and notice a world of diffrence
  2. 873Stang

    cluthch pedal?

    hey if you puch the clutch pedal in it pulls on the cable right? so if i wanted to have it push how would i do that? i might convert mine to hydrallic clutch, so im trying to fig out how i would get it to push the clutch master cylender??? :shrug:
  3. 873Stang

    stock valve covers

    ok so i have my 50 tore down i dont like putting dirty parts on so i cleaned the intake and down im doing the valve covers. is it possible to polish them to look like chrome?????
  4. 873Stang

    clutch master cyclender

    how hard would it be to intall one on an 87 what mod and fab would i have to do has any one one this does it hao be lined up with the clutch pedal thx
  5. 873Stang

    trans which one?

    ok so heres are my options: 1) buy a gear kit for 1700 holds up to 700hp + rebuild kit 213 2) buy one with the same gears for 2,300 company is called astroperformance so thats what im thinking unless someone has a suggestion thx oh what diff is to run with a 2.95 first gear (3.73 or...
  6. 873Stang

    BBK Longtubes.. INSTALL ???

    bbkperformance.com should have the gaskets if not then mr. gasket or brothersperformance.com
  7. 873Stang

    what cleans

    hey what can clean all the oil and gunk off my intake its really bad also when i put it back on what does it get torque to?
  8. 873Stang

    who heard of or is running ( astro gears )

    thinking about getting those geares rated for 450flb of torque 550hp for 1500 is that good with a 2.95 first gear and is there any performance yoke i could buy thx
  9. 873Stang

    how much was your trans work (t5)

    hey just trying to get an idea of what im going to be looking at for a trans any help would be great
  10. 873Stang

    speedo

    it doesnt stay steady till about 80mph
  11. 873Stang

    awwwww crap burning oil help

    thanks guys yea rear main seal is new! yea i have to look under that beast and check would hd 30 be to thick if so what oil would you recommend
  12. 873Stang

    awwwww crap burning oil help

    ok so im burning more oil then i should be, its a stock 5.0 and when i checked the dip stick it had a little tear drop at the end of the dip stick so im guessing it needs 4qt to be where it should. i did my last oil chenge about 2 months a go. now what could be some causes for this?? car has...
  13. 873Stang

    codes 44 & 94????

    44 - air sys management inoperative 94- secondary air sys inoperative what does this mean??? thank you
  14. 873Stang

    Starter replaced ( Flywheel Teeth worn )

    hahah brings back memories, yea i went through two starters before i did my flywheel ($114) and my old one was warped and teeth were worn, after that no prolems sence! so im sure in about a week to a month it will or might start doing it again then you know its the flywheel
  15. 873Stang

    what in thee helll bobby???? (comp)

    ok so today i was looking at my comp, its a da1, now on the do not remove sticker it saids 3.0 taurass/ sable only looked it up on fordfuelinjection.com it saids da1 is for 5.0 mustang so now im confuesed lol whats your thoughts or knowlegd??
  16. 873Stang

    x3z comp

    yea im on a stock motor
  17. 873Stang

    x3z comp

    hmm what size inj can i use with a a9l comp??? 19lb should be good right??? and maf would i use with it???
  18. 873Stang

    how do post

    a classified??? i have louvers i wanna sale
  19. 873Stang

    x3z comp

    the cobra computer would if give my coupe more power? if so how much over s/d computer? 24lb inj with 70mm maf
  20. 873Stang

    harmonic balencer

    if its bad what damage can it cause???
Top Bottom
Back
Forums
Menu