Search results

  1. 2oo3MustangGT

    little photoshoot

    perhaps too good looking, i like it all. what suspension set up is that? that's the stance i was looking for, but missed with my springs...too much wheel gap on mine, yours is perfect. good clean looking ride. i don't always like the smoked rear lights but with the center blacked out that...
  2. 2oo3MustangGT

    suede headliner install help/opinion

    so i finally got it all out of the car, apparently ford does not want you doing this to your car. the stock headliner is the foam/fabric on a pressed cardboard backing, glued to plastic around the doors and then entirely glued, serious stuff, to the roof of the car. this does not peel off at...
  3. 2oo3MustangGT

    suede headliner install help/opinion

    Help! I'm in the cat now trying to do the headliner and it is firmly glued to the actual roof of the car. I can't seperate the foam or get of out of re car. What do I need to do?????
  4. 2oo3MustangGT

    Chin Spoiler Problems?

    i've got mine down 1.5" too and i have only hit once... but it was definatley one too many. i'm extremely careful though. i usually back into parking spaces so clearing the bumper isn't a problem, but if i do pull forward i just make sure to stop short b/c you will hit most curbs, at least the...
  5. 2oo3MustangGT

    birmingham 45th anniversary event at barber

    so unfortunately i can't make it to this event, but i do live here in birmingham and i work downtown by the highway and for a solid 30 minutes nothing but mustangs drove by... they even had police blocking on ramps and escorting them through stop lights. i'm not sure how many people are at...
  6. 2oo3MustangGT

    Ordered a few body parts!! Anything else I should get painted while its in the booth?

    i was going to say paint the mirrors, i want to but havn't yet. there would be some prep to smooth them over and get ready for paint, but you won't have to buy the cobra mirrors.
  7. 2oo3MustangGT

    suede headliner install help/opinion

    not at all actually, i got 4 yards of charcoal suede for $18. got it from an ebay seller, there are a few on there, i got samples from a couple different ones, and some of them were complete junk. my friend bought light gray suede for his car at $15 per yard from a fabric store and it's just...
  8. 2oo3MustangGT

    suede headliner install help/opinion

    that's basically want i want. i figure i can get the headliner, shift/brake boots, front door panel armrest, and a-pillars covered myself. i'm going to find someone hopefully that might be able to cover the rear window trim and maybe make a suede armrest for the back seat panel too.
  9. 2oo3MustangGT

    How To: Make Your Pass Window 1 Click Down

    i thought about trying to buy a drivres side module and installing it to the passenger button, not sure if it would work though. don't see why it wouldn't but i'm glad this kit is out there. it bothers me to touch the drivers button once but hold the other one...even though the window only...
  10. 2oo3MustangGT

    suede headliner install help/opinion

    i will deffinately post pictures when i finish. i agree if things are over done (like the pillars) it cheapens the car, i just don't like how much plastic ford uses. nicely covered peaces can add value i think, but it could be a risky move like you said- don't want a cheap street rod look at all!
  11. 2oo3MustangGT

    official 4.6 liter Mustang photo thread

    here's a few pics of mine, i'm about to redo the headliner and some interior pieces in charcoal suede and then i plan on fully detailing it and having a photo shoot... but for now here's some iphone pics after a quick wash
  12. 2oo3MustangGT

    Post your gauge setup and interior shots

  13. 2oo3MustangGT

    suede headliner install help/opinion

    i just got dark charcoal suede to redo my headliner in my 03. my plan is to wrap the a-pillars and obviously the headliner, maybe do the shift boot/parking brake and maybe steering wheel too? first question, my original headliner is fine, should i just cover the existing stock headliner...
  14. 2oo3MustangGT

    Dynamat vs raammat bxt... Installed, pics, comparison

    fatmat is the same stuff as the peel and seal, it does work , but raammat is a butyl based material which sticks better and has better noise/vibration absorbtion. but the stuff from lowes will definately help, but i would definately not spend the money for fatmat, although i think they have a...
  15. 2oo3MustangGT

    Anyone using these on there gauges?

    i havn't used those on my mustang, but i had the same thing on my audi a4 and loved them. those look really good, i may buy some too. on my audi i couldn't get the clear cover off so i had to fit the trim rings from behind the gauges, made it diffiuclt, and i spilled a little drop of glue on...
  16. 2oo3MustangGT

    Dynamat vs raammat bxt... Installed, pics, comparison

    RAAMaudio - Quality and Value in Automotive Sound Deadening i used 2 full rolls of raammat bxt, and bought 6 yards of ensolight-that's plenty to cover the entire car
  17. 2oo3MustangGT

    Dynamat vs raammat bxt... Installed, pics, comparison

    so i just finished installing raammat bxt in my 03 and am helping a friend install dynamat extreme in his jetta. there is a little bit of difference, the raammat is a little thinner but it also seems to be stickier. let alone i bought enought to cover the entire floor, double in most areas...
  18. 2oo3MustangGT

    Got a couple new parts installed, pic whore time!

    looks great, i'd for the money, get the AM one and if it's too shiney, just put a little flat black paint on it to knock the shine down
  19. 2oo3MustangGT

    Debating swap to SLP exhaust from Flowmaster...any thoughts appreciated

    i have the loudmouth 1's with stock headers/ h-pipe and love them. flowmasters sound good but everyone has them, slp is very loud and a completely different tone than flowmaster. it has a very agressive idle/ low rpm rumble and is very loud at wot... i love the set up and i'm sure with ford...
  20. 2oo3MustangGT

    autometer oil temp install. need some help

    so i've done the t-fitting and the pressure gauge works perfect, but i can't get a reading on oil temp. i don't think oil is flowing...it just fills up cold and sits there. the guage works, i took it out thinking the gauge was broken and put it in boiling water and it immediately read the...
Top Bottom
Back
Forums
Menu