Search results

  1. J

    Stock Speaker replacement

    i am not familiar with those stock speakers, but it looks just like it is a housing to plug a harness into. Is something supposed to plug in there? what does it look like? i'm guessing just cut the pigtail and put on some spade connectors, then attach to your new speakers.
  2. J

    Stock Speaker replacement

    on my 85 4 bangger coupe, 5x7's are stock. dunno if you have a the premium sound or not, but it should also just hook up like the door speakers.
  3. J

    engine swap question -

    i think it is easier to install the motor with the tranny at the same time. makes it easier to line up the clutch and what not while it is hanging in the air, rather than fighting it from under the car. if you are auto i dunno, but a 5 speed or manual tranny, this is the way to go. if you are...
  4. J

    Need a descriptive answer - tach question

    on my car it is the green wire. if you stand in front of the car it is the one on the right.
  5. J

    handheld tuner available

    anderson PMS is prob what your looking for. it is handheld, piggy backs with the stock computer. you do have to leave it hooked up if you want to use its features, so its not like a chip burner. you can adjust stuff like rev limiter, injector pulse, fuel curves and more. it is pretty much plug...
  6. J

    Electric Fan Doesnt Work Anymore

    check to make sure power is still getting to the fan controller. also check the temp probe as well. make sure any and all jumpers are still pushed on.
  7. J

    Pinion Angle and Lowering

    it sits under the carrier and looks like a dogbone kinda. think it is hard rubber.
  8. J

    TFS Stage 2 Cam vaccum?

    well the comp XE274r is kinda similar to that cam. i was getting about 12#'s at idle. i still wanna recheck to make sure though.
  9. J

    What Drag Radials Should I Buy????

    The MT's seem to be the good choice right now.
  10. J

    Trying to change out clutch cable...

    then also if you put it on at the quad, then put it on the fork, wouldn't you still have the same problem?
  11. J

    What lifters, pushrods, Rockers and Valve springs?

    there are numerous post about this subject, but here is a start how to make your own lifter http://www.trickflow.com/articles/stroker_1/# walk thorugh of it. http://www.mustangcentral.net/tech/geometry.html
  12. J

    Trying to change out clutch cable...

    put it on the quad first, then you can use a big prybar on the move the clutch fork to move forward and slip the cable in.
  13. J

    What lifters, pushrods, Rockers and Valve springs?

    you won't know what length you need until you check it with the adjustable pushrods. then you order your pushrods once you have the CORRECT length for your application.
  14. J

    What lifters, pushrods, Rockers and Valve springs?

    for rockers any good name should work fine. comp, crane, scorpion, harland sharp will do great. for pushrod length, you will need to get a set of adj. pushrods, cost like $15 or so. for the springs, if you are gonna get the AFR's, just go ahead and get that spring upgrade they have or whatever.
  15. J

    FPR in the way of EGR w/ TFS TRack heat intake

    have you bent the fuel rail any? i had to do a little "custom bending" on mine in that area to help stuff clear.
  16. J

    Pinion Angle and Lowering

    also if your dogbone thingie is off of the rearend it may be part of the prob. it is supossed to help keep vibrations down. some folks it helps, others it doesn't. and sometimes just the gear change can do it too.
  17. J

    Pinion Angle and Lowering

    something like this would work. you may need to look for one with a finer set of degree marks though. http://www.sears.com/sr/javasr/product.do?BV_UseBVCookie=Yes&vertical=TOOL&pid=00939830000
  18. J

    Pinion Angle and Lowering

    you can get a angle meter/finder thing at sears. you just place it under the rear axle at the pinon/yoke area to get your reading. i think around -2* is ideal. others will have a better answer.
  19. J

    Extra Plug Wire?

    fuel filter is kinda big i think too. about the size of i guess the oil filter as well. it is in front of the gas tank, right about the rear axle i think. peek under there and you will see the lines running to it. be gentle with the plastics if you filter didn't come with new ones.
  20. J

    351w swap....which flywheel needed?

    thats correct, as long as you know it is 28oz balance, then your good to go.
Top Bottom
Back
Forums
Menu