Search results

  1. 9

    How can you tell if your intake is leaking?

    What is the best way to do a vacume test?
  2. 9

    How can you tell if your intake is leaking?

    no, havent puled any codes yet but will maybe try that this afternoon.
  3. 9

    How can you tell if your intake is leaking?

    My car stumbles in idle and the exhaust smells rich. This is after I put a systemax intake and some ported heads, the only part that really bothers me is the stumbling, could the intake be causing this or could there be anything else that would couse this after that type of workk is done?
  4. 9

    who has a box style upper?

    Just put a comp cams upper on my car and have a few questions. What should I do with the harness that hooks on the factory upper, there is no place for them to sit now that I have this box intake. Also Dose anyone know how to route the vacume lines, there was 5 lines that went to the factory...
  5. 9

    EGR Blockoff plate dimensions

    What is the benefit of blocking it?
  6. 9

    advise on intake install

    So use no silicone at all except on front and back seals. Can anyone confirm this?
  7. 9

    advise on intake install

    advice on intake install I am installing my systemax intake and want to know if I need to put any silicone on the intake gaskets. The thing is that it is mounting to stock heads and I am using stock gaskets therefore the crush ring on the stock gaskets may not be crushed since the intake ports...
  8. 9

    advise on intake install

    I am installing my systemax intake and want to know if I need to put any silicone on the intake gaskets. The thing is that it is mounting to stock heads and I am using stock gaskets therefore the crush ring on the stock gaskets may not be crushed since the intake ports are so big. I checked with...
  9. 9

    gaskets for a Systemax lower intake

    anyone?
  10. 9

    gaskets for a Systemax lower intake

    What gaskets do I need for a systemax lower, can I just use the stock ones?
  11. 9

    porting my heads, have question?

    ttt
  12. 9

    porting my heads, have question?

    I am porting my heads right now and have the exhaust side finished but I nicked the valve guide in one of the ports, my question is how do I smooth this out so it does not cause any problems? Also how far is the water jaket on the floor of the exhaust ports, how much can you take off?
  13. 9

    Tilt wheel in a '90GT

    As you know the '90's didn't come with a tilt wheel but did have the air bag, is it posible to put in a tilt column and keep the air bag steering wheel still functional?
  14. 9

    anyone know the equivelent in Mr. Gasket to Fel pro 1250 intake gasket?

    Shop in town only carries Mr. gasket do you know the equivelent to fel pro's 1250?
  15. 9

    how many times can you reuse stock head bolts?

    There were two different style of bolts the flanged style and non-flanged, the flanged are to yield the other is not.
  16. 9

    Gasket matching intake ports - 1262???

    Thanks
  17. 9

    Gasket matching intake ports - 1262???

    how much bigger is the 1250 than stock?
  18. 9

    Gasket matching intake ports - 1262???

    Some say that the 1250 is asa big as I want to go, is this true? Or should I go with the 1260 and open up the ports on the lower to match?
  19. 9

    Gasket matching intake ports - 1262???

    What is the best gasket to match the intake ports to, I have a Holley lower. I was thnking the Felpro 1262 would that be best??
  20. 9

    how many times can you reuse stock head bolts?

    should I oil the head gaskets before installing them?
Top Bottom
Back
Forums
Menu