Search results

  1. No.11

    bad motor mount?

    I have the transmission off right now. trying to remove flywheel bolts and found that there is easy movement of the engine. I can move it around by hand. is this normal with the transmission off or do I have a bad motor mount? thanks.
  2. No.11

    The damn 10-pin connectors...

    will try that, there's a lot to do in that engine bay...
  3. No.11

    The damn 10-pin connectors...

    had them this way and took them off because I read the cables are too tight with its on there and can cause a faulty connection. gonna try cleaning again and zip tie them somewhere safe.
  4. No.11

    The damn 10-pin connectors...

    I just have them sitting off to the side kind of leaning on the EGR, and no extensions. What's the best way to have them mounted without stretching them or letting them hang?
  5. No.11

    should I be concerned with this flywheel?

    got a part number on this? lol
  6. No.11

    The damn 10-pin connectors...

    I have an intermittent misfire, usually is most noticeable as a series of pops and hesitation between 2k and 3k RPM. Cylinder balance test comes up clean. I also have a frequent code 31 for EVR... not too long ago I cleaned the ten pin connectors and my car ran GREAT for about two weeks. then it...
  7. No.11

    should I be concerned with this flywheel?

    gotcha! glad it's no a bigger deal. wanted to get this done in the weekend.
  8. No.11

    should I be concerned with this flywheel?

    ah so it's ok then... even if the scratch is deep enough to catch my fingernail? at what point would a scratch on a new flywheel cause any problems?
  9. No.11

    should I be concerned with this flywheel?

    I received my ford racing flywheel from american muscle along with a few other goodies. everything looked good, except for this scratch on the clutch side of the flywheel. should I be concerned with this? I bought brand new stuff so I wouldn't have to worry about getting something damaged... I...
  10. No.11

    Flywheel Bolts Questions

    yup just received my arp flywheel bolts from cjpony yesterday. look like the same size as the napa ones.
  11. No.11

    Is an aluminum driveshaft worth it?

    Back from the deeeeeaaaaaaaaad! Looking into getting an aluminum driveshaft since I'm gonna change the clutch and its gonna come off anyway... got a question about this rubbing though. Does the rubbing occur on the bracket right underneath the ebrake only? Anywhere else? Also, just to clarify...
  12. No.11

    WTF dark theme?

    sorry noobz, same here. then again I have bad eyes.
  13. No.11

    Torque Boxes on a Fox Install

    never mind.
  14. No.11

    3G swap... now battery light turns on

    yep did it the right way now. thanks! I guess I figured American muscle would have made sure the writeup was good. so how about the ground? 4g required or recommended?
  15. No.11

    3G swap... now battery light turns on

    yep I was running the 4g to the solenoid the whole time... and then the orange black wire also. took those off so now only the 4g to solenoid. should I get a 4g ground as well?
  16. No.11

    3G swap... now battery light turns on

    if not I guess ill have to take it to get checked. edit: according to the installation manual from pa (not the American muscle customer one), I should be fine if I'm charging at over 12.5 volts at idle. guess I'm good to go. a little test showed good results. I turned the high beams on, then...
  17. No.11

    3G swap... now battery light turns on

    ok did that, seems like its charging, not quite at the 14.5 volts I was getting yesterday on the battery. it's at around 13.3 right now. that ok?
  18. No.11

    3G swap... now battery light turns on

    so... this write up by a customer on americanmuscle's website is the wrong way to do it? http://1.cdn.lib.americanmuscle.com/files/95304_95311.pdf and all I need to to is disconnect the two orange/black wires from the gold terminal? and tape them up and leave alone? and I need nothing else to...
  19. No.11

    3G swap... now battery light turns on

    wait are we talking about the same wire? I had the power wire kit from pa performance. the other wires should come out?
  20. No.11

    3G swap... now battery light turns on

    will check on that mike, thanks. pretty sure it was on tight, even heat shrunk it. but will check my soldering also for good measure.
Top Bottom
Back
Forums
Menu