Search results

  1. LILCBRA

    Yet another v8 swap

    No, that is for a Fox. Mustang IIs get a front sump pan that hugs the crankshaft on the back half to give clearance for the rack and pinion. Here is a pic comparison of 2 different front sump pans, one being for the II.
  2. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    I've thought about relocating it to the hatch area, just haven't committed to it. As for the creases in the banner - I've not thought much about it much. I'm wondering how the freshen function of my dryer would work or if I could just use a low heat setting for like 20-30 minutes. :shrug:
  3. LILCBRA

    Vibration after new clutch

    The more I think about what you're saying the more I think it's some sort of alignment issue with the input shaft. Were all of the mating surfaces cleaned as best you could before reinstalling everything? When you installed the transmission, did it seat cleanly before bolting it in or did you...
  4. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    This should help.
  5. LILCBRA

    Vibration after new clutch

    Welcome to :SN: ! So the problem wasn't present before the swap, or was it? And your checks were done with or without the driveshaft to eliminate driveshaft issues? My first instinct is something to do with the input shaft of the transmission. Whether that's the pilot bushing, a bad bearing...
  6. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    This cooling duct is cracked and missing a piece, but I've saved a few on Ebay since your last suggestion. I'll probably pull the trigger on one sometime in the relatively near future. Speaking of Ebay and pulling the trigger - I couldn't help myself and pulled the trigger on one of these a...
  7. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    Tonight's progress: Pulled the engine harness, the firewall braces, and made templates for the hole locations for those braces as well as the T top roof if I need it. It's about time to climb around inside the car to remove the dash but, if I'm being honest, I'm not looking forward to it. I have...
  8. LILCBRA

    Yet another v8 swap

    Hi Bob! What clarification are you looking for? As @Blackhawkxx said, the oil pans are unique in order to clear the rack and pinion. Exhaust can be one of the most challenging parts of it all since it's so tight. Ford made a smaller flywheel/flexplate and corresponding bell housing specifically...
  9. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    I'm in Iowa - cold is mandatory, snow is optional. ;) I don't remember seeing it on any shows or anything, but I have seen it done in salvage yards, specifically in vans with engines missing. Having pulled an engine and transmission combo from a II multiple times over the years I know how...
  10. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    I'm planning on drilling all of the rivets and cutting all of the stitch welds from the T top support before transferring it to my car. I'm not sure if I'll be able to use it as a template for my cuts, but that's the hope. If not, I picked up some poster board to use as a guide. But my overall...
  11. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    Progress overnight tonight - got the engine and transmission pulled. Made a slight mess, forgot to plug the transmission tail shaft. :doh: Good thing I have a few restaurant sized trays laying around to catch this kind of stuff or it probably would've been worse. Since the lower radiator support...
  12. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    I suspect it is/does, especially since my engine produces a bit more torque than the stock 302. I had home made connectors in it before I went with Stumpy's a few years ago, I suspect they weren't quite as good at preventing the twist.
  13. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    My back has been feeling a lot better but I ended up running a few errands instead of working on the car today. I did, however, pick up a load leveler for my engine hoist and dropped that in the garage. Here's something that I'm sure more than one of us has experienced: I believe the web...
  14. LILCBRA

    Progress Thread Today in the shed........

    I see Black Hawk plates on the GT/CS - I grew up in the 'Loo! A buddy traded his 04 Mach 1 in for a newer 5.0 PP car though I don't remember exactly what his car's package is. Anyway, he generally babied his Mach 1 and I believe it only had ~40k miles on it (I don't remember what he said the...
  15. LILCBRA

    Random Mustang II Pictures

    The more I play with this render the more I think someone should build it.
  16. LILCBRA

    Grown Man Crying

    Here you go Pete, if you've not found it already. Maybe this will help.
  17. LILCBRA

    Progress Thread The next "big" project for my Cobra - T-top conversion coming soon!

    I have parts! :D And here's the ongoing battle with the rockers now - they're doing nothing but get worse. I was seriously planning on starting the process of tearing the engine and transmission out of the T top car tonight, unfortunately my lower back screamed "f-off!" so there will be...
  18. LILCBRA

    Injector question

    They look correct as near as I can tell. :shrug:
  19. LILCBRA

    Red convertible in East Tennessee

    Welcome to the group! :SN:
  20. LILCBRA

    Hello, from Illinois

    Welcome to :SN:!! Love to see the progress once you get started! :nice:
Top Bottom
Back
Forums
Menu