Search results

  1. rbohm

    Which transmission fits my coupe ?

    the only differences between the V8 and six cylinder C4s are the number of clutches in each clutch pack in the trans. the six cylinder C4s can be upgraded to V8 specs if you want easily. also the accumulator piston is different as well. as far as i know the C3 never came behind the inline six.
  2. rbohm

    Heidts Mustang Ii Info And 429/460 Swap

    not necessarily, remember in 67 the 390 came in the mustang, and many were backed by the C6 trans. OP, you shouldnt need to cut up the car to install the 460 in your 68, again because these cars came with the brawny shouldered FE motors.
  3. rbohm

    EFI 351 Swap?

    the crown vics had the 351w in them, after 1982 they were used only in police cars. also there were a handful of factory built 1993 mustangs that had teh 351w installed as well.
  4. rbohm

    Back To The Front? Trump "Recalling" IRR and other "Former" Troops

    just remember if they put you on the front lines, kill everything and let god sort it out, its his job anyway. :D:D:D:D
  5. rbohm

    Custom Cams?

    for the vast majority of engine builders, off the shelf cams work just fine. you just need to select the cam that fits your build as closely as possible. where custom grinds come in is when you are going for something that is designed as a one off cam specifically for your application. some...
  6. rbohm

    Back To The Front? Trump "Recalling" IRR and other "Former" Troops

    OP if oyu get recalled back to service, you wont be going back as infantry. you would be going back in as a REMF
  7. rbohm

    EFI 351 Swap?

    for cars in that era with the 351 efi engines, ford flattened out the upper intake s it would fit under the hood. however for trucks and van they had no issues with hood clearance, so the upper intakes were indeed taller by about 4-5 inches as i recall. that said however, if you scare up the...
  8. rbohm

    289 t5 questions

    first make sure you have the correct imbalance factor on the flywheel. for your 289 it should be 28oz imbalance. as for the clutch itself, if the flywheel has the bolt pattern for the pressure plate, then you can us the newer pressure plate and disc with no issue. the bell housing will fit the 6...
  9. rbohm

    crossthread

    i have done things like that before, it happens regardless of how careful we are. i remember rebuilding a one barrel carb for my 66 falcon, only to find that i had stripped the screw holes in the body that held the carb top on. made my decision to convert to a two barrel carb and electronic...
  10. rbohm

    crossthread

    more power to you. like i said use a bottoming tap, not a starting tap since you have no room to use a starting tap. the bottoming tap is flat on the end with no taper. and again make sure you get it as absolutely straight as possible. and take your time.
  11. rbohm

    crossthread

    that makes things a bit tougher, but still doable. if you are careful you can use a bottoming tap to cut new threads, and then use a brass fitting to replace the screw in filter, and go with an inline filter. be very careful though if you go this route as you MUST BE ABSOLUTELY SURE that you...
  12. rbohm

    crossthread

    easy enough to tell which carb you have with one question, is the float bowl removeable? if so then it is the holley carb. holley carb autolite carb
  13. rbohm

    1967 transmission dylema

    that will depend on which T5 you choose. get the V8 T5 and you should be good to go.
  14. rbohm

    1967 transmission dylema

    the T5 swap is pretty straight forward. in your case you will need to find either a complete kit that includes a bell housing, as well as the proper adapter plate, 9" flywheel, clutch components, etc. check with modern drivelines they should have everything you need. contact...
  15. rbohm

    Old time member looking for help: 1970 vs 1995

    glad to see you made a choice, and it was a good one. given the amount of upgrading the early car would have needed to get the handling up to where you want it, you would have spent a lot more money than on the 94. as for the 393 stroker kit, it would ahve been cheaper to do your own since you...
  16. rbohm

    3D printed spoilers?

    if you can design it yourself, you can then take the program and have someone do the printing, since i doubt you have the money or space for your own 3D printer large enough to do the job. look for companies in your area that do rapid prototyping.
  17. rbohm

    rear gears

    for 125 rpm? not worth the effort or the money, since you will never notice the difference.
  18. rbohm

    Brakes

    i did this conversion on my 64 falcon. a few bits of steel line with the ends already installed, including the flares, a few adapters, "T" fittings, etc. and a 67 mustang drum/drum master cylinder, and an hours work. the basic conversion itself is easy. national parts depot has a conversion kit...
  19. rbohm

    rear gears

    the rpm difference is very slight, something like under 50 rpms if i recall correctly.
  20. rbohm

    Brake conversion

    correct. most people somehow think that adding power brakes means the car will stop better, but it wont. power brakes just means its easier to use the braking ability of the car.
Top Bottom
Back
Forums
Menu