Search results

  1. mfp4073

    Help With Hestitation/Stumble Problem - Thanks

    Popping back through the carb is almost always timing related. There may be other stuff going on...but that is where I would focus.... If its crappy and timed right it will go out through the bottom, not the top.
  2. mfp4073

    Mach 1 from the Forest ( with Pics )

    how much did they want for it again?
  3. mfp4073

    Anyone running locked out timing?

    I dont know. I ditched my vac advance with my MSD drop in distributor. It harmed me trying to use it (while tuning on a dyno) and have no drivablity problems either. I actually roughed up my idle my messing with my idle mixture and idle speed.
  4. mfp4073

    Need pic: GT350 w/ red stripes over driver's fender

    I asked this several years ago....and came up with the same info....its so teams with similarly painted cars could ID who what who.
  5. mfp4073

    Stock UCA's and Shelby drop

    the upper control arm relocation will only drop the front end by 1/4 of an inch. I HIGHLY recommend it for anyone wanting better control over the car. If you look at the geometery, the 1 inch drop on the body side will only translate to about a 1/4 inch on the actual ride side. I replaced my...
  6. mfp4073

    Stock UCA's and Shelby drop

    +1, no problems. Just if you are in there, consider replacing some of the front end stuff while you are at it (if its not current)
  7. mfp4073

    where can I buy a 9" posi clutch kit?

    8" and 9" are the same for the traction loc.
  8. mfp4073

    HEATER WONT SHUT OFF (HELP)

    if you are not hearing the blower motor blowing, but just kinda getting a trickle of warm air, its probably a result of your heater box needing to be redone. Basically there are flaps in there that keep the air from traveling through the heater core. When they get damaged or whatever you will...
  9. mfp4073

    rear gears question

    my 3.89s are about 4000rpms at 80, i think 3.55s would be a little more enjoyable for me.
  10. mfp4073

    Ford Racing Crate Motors?

    I bought one of the first of the gt40 longblocks several years ago (before they were even listed in the ford catalog). Not a problem of any kind so far.
  11. mfp4073

    Look at this ebay find....

    haha, its an overseas car....in the middle east.....you got to be kidding me. The fact that its another Eleanor clone is the least of the problems with this auction.
  12. mfp4073

    1965..289 motor. Is it worth anything to anyone?

    I tell you what, I had an unbored 66 289 4bbl that still had life in it a couple of years back. Without shipping it, I did not have a lot of luck finding a buyer. I finally let it go for $200 as a longblock just to get it out of my way.
  13. mfp4073

    Squeezing a new engine in a 67 Coupe

    up to 390 class motors will fit in there from the factory....I will not tell you what you have to do to change the spark plugs, but they fit!
  14. mfp4073

    Holley Carb Fuel Slosh question

    I had problems with stuff like that fitting under my air cleaner. I never did solve it completely, but then I dont drive my car much these days.
  15. mfp4073

    Holley Carb Fuel Slosh question

    yeah, what dhearne said, the decelleration (sp) bog is due to the fuel int he rear bowl sloshing forward and up the vent tube...then into the carb.
  16. mfp4073

    Holley Carb Fuel Slosh question

    you should be able to get the car to grab with a stab of the throttle. Its the cams that get you this....it basically leans out when you jab it open, the cam squirts extra fuel in there. They are cheap to get a set and just keep trying different ones until you get the result you like.
  17. mfp4073

    widest tires in back in stock wheel-wells?

    I got 265s back there...probably could get a little more...but it would be VERY close.
  18. mfp4073

    Dyno run pre-check list

    I had mine done, for just a little bit more the place would do the tuning for you. In my case this worked out great because there were some problems with the machine and the guy doing the tuning had several phone calls while I was standing there paying him. Basically he did 3 hours of tuning...
  19. mfp4073

    Going to Restore my '67 - Please chime in with helpful advice

    Im not sure here, but you may have more work than you realize. If I am correct, 4 lugs were for 6cyl cars. Being that you say you have a 289, someone had to have changed it over without doing the suspension upgrades to go with it. Its hard to say just what has and hasnt been done and I am no...
  20. mfp4073

    Muffler Placement

    You know, I have no idea. Us bench seat car owners dont have to worry about those inside seat bolts:lol:
Top Bottom
Back
Forums
Menu