Search results

  1. blackfang

    Next mods for a 99 Cobra?

    You should swap out the 3.73's for some 4.30's if you plan on staying NA
  2. blackfang

    97 Cobra suspension

    If you are going with a Panhard bar, there is no sense keeping the UCA's. You should install a Torque Arm with it.
  3. blackfang

    97 Cobra Headers?

    I loved my LT's. I definitely felt a huge low and midrange gain. The install wasn't too bad. I ran flowtechs for a few years without any leaks or issues. Still able to drop the trans if needed too. Plus the car sounded sick as hell when you got on it too:D Again do not focus on the peak power...
  4. blackfang

    Trans AM

    I sold it back in October for another bike. I pretty much lurk a lot now.
  5. blackfang

    quad shock ?

    I'd replace them. Believe it or not they serve a purpose as the Mustangs suspension you have isn't the greatest design. Leaving them in will help, unless you go with a TA/PHB/LCA setup.
  6. blackfang

    Trans AM

    Just go out and race him. if he wins, mod the car some more, but simply a bolt on car driven by a good driver is a mid 12 second car. I am not going to get into LS1's and how they react to mods. GL
  7. blackfang

    Worst Service ever at Livernois Motorsports

    Ok maybe he did committ to them because they were (like many shops do) expecting parts to arrive on time. Sadly there are times when parts are delayed which can and can't be controlled by the shop. Also finding additional problems during the repairs/installs also delays original estimates(that...
  8. blackfang

    Worst Service ever at Livernois Motorsports

    Wow, this got interesting now the other side of the story is out. Damn! OP- who welded the exhaust?
  9. blackfang

    HELP! HELP! 96 COBRA Loss of Power At Hight RPM

    :eek: Try gapping them at .035 and see what that does. Also have you checked the wires for any arcing? What about the A/F sensors(what are they reading?) and is the MAF clean?
  10. blackfang

    4.6l Dohc !!!

    Yes, for the most part that will bolt right in. Might as well get a 96-98 Cobra intake as they bolt on the B heads of the 93-97 Mark VIII. You can also do a short runner intake w/ a IMRC delete(you will need to 4.30's or more to overcome to the torque loss) and enjoy more mid-high range power w/...
  11. blackfang

    Noob with clutch question

    IIRC, they all have the adjuster on the clutch pedal unless it has been removed. Like it has been said. With the car off, in gear, just pull up on the clutch pedal slightly until you hear clicking. Welcome BTW.
  12. blackfang

    NOT your typical LT header ?

    My old 97 sat lower in the front and I had LT's. The car would scrape if i took a bump head on and sometimes even if i went at an angle. It wasn't that bad, but can be a pain if you weren't careful.
  13. blackfang

    Another LT1 talking

    Now some more info is coming out by the other kid. Those gears are dogs. Even the LSx cars had them too.
  14. blackfang

    Another LT1 talking

    It all depends. I have seen LT1 auto's with a cold air kit and mufflers run 13.6 and stock ones run 13.8 w/ a m6. OP- I have been around racing and modding numerous Mustangs, owned a few myself and numerous LT1's and LSx cars. There is no way in hell you beat a bolt on LT1 with exhaust,( they...
  15. blackfang

    Quickest mods to beat LS1!!

    Search feature :D This topic has been beaten to death...lol
  16. blackfang

    rear end gears

    If the rear gears are changed and the speedometer gear is changed accurately to the right gear, then no, the miles are true. Now if you change rear gears and do not change the speedo gear or put the wrong one in, then yes the miles will be off.
  17. blackfang

    best way to seal the slip joint on LT's?

    I would use the dynomax clamp. Many have used it with great success.
  18. blackfang

    Diablo Sport and Gears for a '98 cobra

    No, the pre-99's speed are mechanical. A Speedcal will work to recalibrate it. I recommend 4.30 gears though.
  19. blackfang

    Lowering springs/suspension

    It all depends on what you are looking for and what the car needs to do. on my old Cobra, I ran FRPP B Springs, MM LCA's and it lowered my car nicely. It just caused the headers to scrape.
  20. blackfang

    Best front brake pads?

    When I had my Cobra, I had the HPS with zero issues. Definitely recommend them.
Top Bottom
Back
Forums
Menu