• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

5.0 wont start!!!!!

  • Thread starter Thread starter Bay 5.0
  • Start date Start date Jun 16, 2006
B

Bay 5.0

New Member
Jun 16, 2006
2
0
0
Jun 16, 2006
#1
  • Jun 16, 2006
  • #1
1st timer to the forum. My 1992 5.0 was put up for the winter. I started it up about 2 months ago. One morning after parking it in my garage it wouldnt start. No fuel! Ive replaced the fuel pump, & still no fuel. I jumper wired the new pump and it worked. So its not the pump. Ive sprayed in some starting fluid and it ran for a few seconds, so ive eliminated any spark issue. Ive replaced the shut off switch in the trunk, both fuel relays but still wont start. Ive checked the voltage from the pcm and it was over 12, but the voltage at the interia switch is below 6. Pump wont prime when key is turned on. Any one have any ideas?????????
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 16, 2006
#2
  • Jun 16, 2006
  • #2
Fuel Pump Troubleshooting for 91-93 Mustangs

Clue – listen for the fuel pump to prime when you first turn the ignition switch on.
It should run for 5-20 seconds and shut off. To trick the fuel pump into running,
find the ECC test connector and jump the connector in the lower RH corner to
ground.

If the fuse links are OK, you will have power to the pump. Check fuel pressure –
remove the cap from the Schrader valve behind the alternator and depress the
core. Fuel should squirt out, catch it in a rag. A tire pressure gauge can also be
used if you have one - look for 37-40 PSI. Beware of fire hazard when you do this.


No fuel pressure, possible failed items in order of their probability:
A.) Tripped inertia switch – press reset button on the inertia switch. The hatch
cars hide it under the plastic trim covering the driver's side taillight. Use the
voltmeter or test light to make sure you have power to both sides of the switch

B.) Fuel pump power relay – located under the driver’s seat in most stangs built
before 92. On 92 and later model cars it is located below the Mass Air Flow meter.

C.) Clogged fuel filter
D.) Failed fuel pump
E.) Blown fuse link in wiring harness.
F.) Fuel pressure regulator failed. Remove vacuum line from regulator and inspect
for fuel escaping while pump is running.

The electrical circuit for the fuel pump has two paths, a control path and a power
path.

The control path consists of the computer, and the fuel pump relay coil. It turns
the fuel pump relay on or off under computer control. The switched power (red
wire) from the ECC relay goes to the relay coil and then from the relay coil to the
computer (light blue\orange wire). The computer provides the ground path to
complete the circuit. This ground causes the relay coil to energize and close the
contacts for the power path. Keep in mind that you can have voltage to all the
right places, but the computer must provide a ground. If there is no ground, the
relay will not close the power contacts.

The power path picks up from a fuse link near the starter relay. Fuse links are like
fuses, except they are pieces of wire and are made right into the wiring harness.
The feed wire from the fuse link (pink/black wire) goes to the fuel pump relay
contacts. When the contacts close because the relay energizes, the power flows
through the pink/black wire to the contacts and through the dark green\yellow
wire to the inertia switch. The other side of the inertia switch with the
brown\pink wire joins the pink/black wire that connects to the fuel pump. The fuel
pump has a black wire that supplies the ground to complete the circuit.

Remember that the computer does not source any power to actuators, relays
or injectors, but provides the ground necessary to complete the circuit. That
means one side of the circuit will always be hot, and the other side will go to
ground or below 1 volt as the computer switches on that circuit.



diagram of the wiring for 91-93 cars.

Power circuits:
Power feed: Look for 12 volts at the pink/black wire (power source for fuel pump relay).
No voltage or low voltage, bad fuse link, bad wiring, or connections. Remember that on 92
or later models the fuel pump relay is located under the Mass Air meter. Watch out for the
WOT A/C control relay on these cars, as it is located in the same place and can easily be
mistaken for the fuel pump relay.

Relay: Turn on the key and jumper the ECC test connector as previously described. Look
for 12 volts at the dark green\yellow wire (relay controlled power for the fuel pump). No
voltage there means that the relay has failed, or there is a broken wire in the relay control circuit.

Inertia switch: Check the brown/pink wire, it should have 12 volts. No 12 volts there, either
the inertia switch is open or has no power to it. Check both sides of the inertia switch: there
should be power on the dark green\yellow (inertia switch input) and brown/pink wire
(inertia switch output). Power on the dark green\yellow wire and not on the brown/pink wire
means the inertia switch is open. Press on the red plunger to reset it to the closed position.
Sometimes the inertia switch will be intermittent or will not pass full power. Be sure that
there is 12 volts on both sides of the switch with the pump running and that the voltage drop
measured across the switch is less than .75 volts.

Control circuits:

Relay: The red wire for the fuel pump relay coil gets its power feed from the ECC relay.
No 12 volts here, and the ECC relay has failed or there is bad wiring or bad connections
coming from it. The ECC relay is located on top of the computer, which is under the passenger’s
side kick panel. It is not easy to get to, you must have small hands or pull the passenger side
dash speaker out to access it.

Relay: The light blue/orange wire provides a ground path for the relay power. With the test
connector jumpered according to the previous instructions, there should be less than .75 volts.
Use a test lamp with one side connected to battery power and the other side to the light blue/orange
wire on the fuel pump relay. The test light should glow brightly. No glow and you have a broken
wire or bad connection between the test connector and the relay. To test the wiring from the
computer, remove the passenger side kick panel and disconnect the computer connector.
It has a 10 MM bolt that holds it in place. Remove the test jumper from the ECC test connector.
With the test lamp connected to power, jumper pin 22 to ground and the test lamp should glow.
No glow and the wiring between the computer and the fuel pump relay is bad.

Computer: If you got this far and everything else checked out good, the computer is suspect .
Remove the test jumper from the ECC test connector located under the hood . Remove the
plastic cover over the computer wiring, but leave the computer wiring connector plugged
into the computer. With the ignition switch in the run position, connect a test lamp to the
battery and back probe pin 22, the light blue/orange wire with it. The lamp should glow
brightly. No glow and the computer has died a sad death. If you used a voltmeter instead
of a test lamp, you should see battery voltage, whatever that may be…

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine/

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Fuel pump runs continuously: The light blue/orange wire has shorted to ground. Disconnect
the computer and use an ohmmeter to check out the resistance between the light blue/orange
wire and ground. You should see more than 10 K Ohms (10,000 ohms) or an infinite open
circuit. Be sure that the test connector isn’t jumpered to ground.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 16, 2006
#3
  • Jun 16, 2006
  • #3
See Jrichker's checklist, specifically the fuel pump testing part. EDIT: How does he do that.

I like to start at the FP relay (you only should have one) and see what values are missing. It sounds like there's an issue with the inertia switch or the EEC relay output to the inertia switch (if one side of the inertia switch had 12 volts going into it and 6 coming out, that's worth checking and replacing). If you dont have 12 volts making it to the inertia switch, go backwards towards the EEC relay.
If the EEC relay has no power to it, look at its fusible link.

Do you know if the injectors have 12 volts (along with other sensors)?

Good luck.
 

Ny Mustang Guy

Founding Member
Dec 10, 2001
322
0
0
Queens Nyc
Jun 16, 2006
#4
  • Jun 16, 2006
  • #4
You check the fuses?
 
C

criticman

Member
Sep 7, 2003
723
1
16
Rome, GA
Jun 16, 2006
#5
  • Jun 16, 2006
  • #5
May want to see my thread on similar issue should be on page 2 or 3 now...search my name.

It ended up being a dead (fried) fusible link to the EEC relay and the fuel pump. However, if you can jumper it and get it to run, sounds like it may not be the issue.

I would start at the FP relay as HISSIN suggested. Get yourself a cheap test light ($3). I tried to diagnose with a multimeter, and it didn't do so well. 15 minutes with the test light and I found my electrical gremlin. Just go wire by wire off of the starter solenoid's positive terminal with the test light, checking for power before and after each fusible link. That is a sure way to either find the problem, or rule out potential causes.

Good luck.
 
B

Bay 5.0

New Member
Jun 16, 2006
2
0
0
Jun 19, 2006
#6
  • Jun 19, 2006
  • #6
Ill try it

Thanks fellas. Im going to try Jrichker's list and Hissin50's advice. Let you know after the weekend on the outcome.
 
You must log in or register to reply here.

Similar threads

A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
601
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
D
1989 mustang 5.0 crank no start
  • Darkstang302
  • Nov 10, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
181
Fox 5.0 Mustang Tech Sunday at 8:36 PM
AeroCoupe
S
1990 foxbody 5.0 fuel system.
  • staceyj
  • Nov 28, 2025
  • Fox 5.0 Mustang Tech
Replies
8
Views
635
Fox 5.0 Mustang Tech Nov 28, 2025
Mustang5L5
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
247
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
S
92 5.0 almost starts
  • Steverino
  • Sep 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
280
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 25, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?