• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

'86 5.0 H.O question....

  • Thread starter Thread starter Vinnietbird
  • Start date Start date Mar 13, 2006

Vinnietbird

Member
Jun 2, 2005
584
3
19
Mar 13, 2006
#1
  • Mar 13, 2006
  • #1
I have an '86 5.0 H.O in my '88 Thunderbird.It's a stock Speed Density engine (Mustang computer also) with an Explorer intake and 1 5/8 headers,true dual exhaust with H-Pipe,and a 58mm throttlebody (I had to get one from a Mark VII because my engine didn't have one).My questions are....What is the biggest throttlebody I can use without going too far?I have a 60 and a 65 in the garage.Are the 1 5/8 headers overkill?Are the 19# injectors adequate?Thanks.
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Mar 13, 2006
#2
  • Mar 13, 2006
  • #2
the speed density is kinda limiting you on alot of aspects.....i wouldnt go much bigger than the throttle body you have now
 

wfriedman

New Member
Dec 31, 2005
39
1
0
Sheridan, Arkansas
Mar 13, 2006
#3
  • Mar 13, 2006
  • #3
If you have an 86 block, you have E6 heads and flat top pistons. Until those are gone anything you are doing is moot.

E6 Heads flow like poo. Hence the 58MM TB and smaller E6 upperintake on a Stock 86HO.

Right now the headers are probably overkill, as is the explorer intake. 19's are adequate.

Right now the heads are the bottleneck.

Tear down the motor, notch the pistons, and slap on some different heads. then a 60 or 65MM TB and the rest of your combo. Big difference then.

86 was the 'teething" year for EFI 5.0s.

86's lost 25hp and 25lbs of torque, over the 87+'s mainly due to those heads.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Mar 13, 2006
#4
  • Mar 13, 2006
  • #4
Modular2v said:
the speed density is kinda limiting you on alot of aspects.....i wouldnt go much bigger than the throttle body you have now
Click to expand...

Crap! Total Crap! LOL Just pickin on ya man.

Your real limiting factor at this point are the E6 heads. They're not so limiting though, that you won't find a gain from running a larger TB. If you've got a 65mm lying around then put it on. I've run as large as 70mm on E6 heads and stock cam and produced a dyno measurable gain from the swap. Don't expect miracles or anything, but you will find a gain there. The 86 SD cam is one of the most agressive of the 5 oh HO OEM cams and will make use of any additional air you can get into the combo. You'd be suprised how much you can wake up that combo with a set of TFS heads and that stock SD cam. On a stock motor... I'd hazard a guess that you're at roughly 75% of the potential for the stock cam (figure pulled out of my rear-end. Just a guess with no hard data to show for it).
 

Vinnietbird

Member
Jun 2, 2005
584
3
19
Mar 13, 2006
#5
  • Mar 13, 2006
  • #5
I have a set of GT40's on the workbench.I hope to get them on soon.Will the headers hurt my engine (performance wise)?I just removed the factory Ford headers and put these on Saturday.The car isat the muffler shop right now geting the cats removed.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Mar 13, 2006
#6
  • Mar 13, 2006
  • #6
I replied to your PM about the GT40 heads but the short version is that you'll not be able to install those heads without either notching your 86 flat tops or swapping them out for a set of 87+ pistons. A bottom end rebuild kit may be in your future.
 

Vinnietbird

Member
Jun 2, 2005
584
3
19
Mar 13, 2006
#7
  • Mar 13, 2006
  • #7
Thanks.
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Mar 13, 2006
#8
  • Mar 13, 2006
  • #8
i have some e7 heads and some windsor heads sittin around if you want them
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Mar 14, 2006
#9
  • Mar 14, 2006
  • #9
i also have 88 pistons, rods and crank if you are interested...Pm me
 

Vinnietbird

Member
Jun 2, 2005
584
3
19
Mar 14, 2006
#10
  • Mar 14, 2006
  • #10
Stay tuned Modular,I may just do that.
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Mar 14, 2006
#11
  • Mar 14, 2006
  • #11
Vinnietbird said:
Stay tuned Modular,I may just do that.
Click to expand...
good deal bud, they are not going anywhere so they are yours if you want them
 

wfriedman

New Member
Dec 31, 2005
39
1
0
Sheridan, Arkansas
Mar 14, 2006
#12
  • Mar 14, 2006
  • #12
I am so ready for an 87-92 Longblock right about now....

Anybody got a spare they wish to donate??

 
You must log in or register to reply here.

Similar threads

J
Engine Tuning...?
  • justadude07
  • May 30, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
398
Fox 5.0 Mustang Tech Aug 21, 2026
Qtrhrse23
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
New Exhaust for 408w stroker
  • SadbutTrue
  • Sep 10, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
168
1965 - 1973 Classic Mustangs -General/Talk- Sep 10, 2026
nickyb
D
Foxbody Misfire 5.0 Swap
  • DPORTER0729
  • May 2, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
783
Fox 5.0 Mustang Tech Jul 13, 2025
90sickfox
Exhaust 1 3/4” Long Tubes on a Fox Body AOD – Easiest route?
  • 5.0 Mike
  • Mar 19, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
2K
Fox 5.0 Mustang Tech Mar 21, 2025
5.0 Mike
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?