• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Drivers side...2 Rich + 2 Lean Cylinders???

  • Thread starter Thread starter zidane45
  • Start date Start date Jul 5, 2006

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 5, 2006
#1
  • Jul 5, 2006
  • #1
my drivers side has the front and rear cylinders getting way too much fuel and then the middle two are not getting enough. The plugs however on the passenger look awesome. I was wondering if anyone has ever ran into this problem. I was wondering if it may have to do with computer or wiring for the efi harness.
Thanks,
 

795.0pacecar

lover of pudgy polygamists
Jul 11, 2003
480
0
17
Senoia, GA
Jul 5, 2006
#2
  • Jul 5, 2006
  • #2
My car has been doing something similar, cylinders 5 and 7 are alittle rich and cylinders 1 and 3 are alittle lean. I too would like alittle insight into this problem.
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 5, 2006
#3
  • Jul 5, 2006
  • #3
Yeah. I'm going to double check all my wiring for the efi. and put new plugs in it for now. ticks me off cause the engines only been in a week.
 

795.0pacecar

lover of pudgy polygamists
Jul 11, 2003
480
0
17
Senoia, GA
Jul 5, 2006
#4
  • Jul 5, 2006
  • #4
I regapped my plugs, and fixed my egr problem, so we'll see if that has any effect.
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Jul 5, 2006
#5
  • Jul 5, 2006
  • #5
Well, that could be a few things. How old are the plugs/wires/cap? It could be dirty injectors, it could be a blown head gasket. Hard to say just by that low of a symptom list.
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 6, 2006
#6
  • Jul 6, 2006
  • #6
well i did a compression test and everything looked great there. Its just when I accelerate I get a lot of smoke. The wires aren't old and the cap and rotor look good. is there something in the distributor that could cause a problem like this?
 

FORCED2DV8

New Member
Jun 6, 2005
458
0
0
Grand Rapids MI
Jul 6, 2006
#7
  • Jul 6, 2006
  • #7
What kind of smoke, is it fuel or oil or water/antifreeze. Like was said before, injectors, Even if the cap and rotor look good they can be faulty, test your wires with a ohm meter, check the resistance. Even if they are new.
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 6, 2006
#8
  • Jul 6, 2006
  • #8
Alright. Hey I'm from the big GR. Well actually byron center. small world.
It smells like fuel. the two bad plugs were all wet when i took them out and pretty black with small little deposits.
 

FORCED2DV8

New Member
Jun 6, 2005
458
0
0
Grand Rapids MI
Jul 6, 2006
#9
  • Jul 6, 2006
  • #9
Looks like you moved to some better weather It sounds like those plugs are not firing, try changing those plugs and testing those specific wires..maybe swap it if you have any extra..
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 6, 2006
#10
  • Jul 6, 2006
  • #10
I broke one of the wires when i took it off so i swapped that with some extras that i have.
It still doesn't make sense why the others would run so lean though. Thats why i'm thinking that it has something to do with fuel delivery or a contributing factor. Like those injectors are starving the fuel from the other two.
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 7, 2006
#11
  • Jul 7, 2006
  • #11
I checked the wiring with a noid tester and it seems to be working properly. Could it be something ignition?
 

fidstang

New Member
Jul 19, 2005
307
0
0
South Lansing
Jul 7, 2006
#12
  • Jul 7, 2006
  • #12
What intake do you have? Stock type intakes suffer from the front and rear runners starving for air(rich cond.). Which could cause the middle two to run lean if the tuning is just on the boarder line. As for the other bank being fine and the problem seems related to one side, check the injectors and harness.
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 7, 2006
#13
  • Jul 7, 2006
  • #13
yea. its stock. thats the thing that gets me. why its just doing it on the one side.
 

zidane45

New Member
Dec 26, 2003
55
0
0
charleston,SC
Jul 7, 2006
#14
  • Jul 7, 2006
  • #14
yea. its stock. thats the thing that gets me. why its just doing it on the one side.
 

fidstang

New Member
Jul 19, 2005
307
0
0
South Lansing
Jul 8, 2006
#15
  • Jul 8, 2006
  • #15
I do believe that the stock intake front runner runs to cylinder 1 and the rear runner runs to cylinder 5. Which is on the passenger side of the car. This is a known problem for the stock and stock type intakes. I would suggest a switch to intake that doesn't suffer from this design issue and will allow the air flow to all cylinders evenly.
 

fidstang

New Member
Jul 19, 2005
307
0
0
South Lansing
Jul 8, 2006
#16
  • Jul 8, 2006
  • #16
fidstang said:
I do believe that the stock intake front runner runs to cylinder 1 and the rear runner runs to cylinder 5. Which is on the passenger side of the car. This is a known problem for the stock and stock type intakes. I would suggest a switch to intake that doesn't suffer from this design issue and will allow the air flow to all cylinders evenly.
Click to expand...
Excuse me, I meant cylinder 4 not 5.
 

fidstang

New Member
Jul 19, 2005
307
0
0
South Lansing
Jul 8, 2006
#17
  • Jul 8, 2006
  • #17
I take that back I just remembered that the front intake runner goes to cylinder 1 but the rear intake runner goees to cylinder 8 not 4. My bad! I would still look at the injectors on those cylinders. How far off are they?
 
You must log in or register to reply here.

Similar threads

T
Fox Convertible top issues
  • TDM389
  • Feb 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
482
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 15, 2026
General karthief
J
Fox Lost all gauge cluster function after Holley Terminator X install (solved)
  • Justin17383
  • Nov 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
278
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 13, 2026
2000xp8
D
Running both lean and rich with O2 heat codes
  • Danceswithfire5
  • Aug 30, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
183
SN95 V6 Mustang Tech Sep 5, 2026
apple99Mustangdude
A
Electrical 88 EEC Injectors batch firing ?
  • Dustin 86GT
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
665
Fox 5.0 Mustang Tech Jan 8, 2026
gkomo
Who the hell puts the wrong spark plugs in a 3.8L?
  • snowstang
  • Mar 25, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
672
1996 - 2004 SN95 Mustang -General/Talk- Apr 3, 2026
LILCBRA
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?