eval my et & what msd rpm chips should i use for 125shot with my mods & nitrous??

96mustang_james

Member

May 20, 2003

199

1

17

atoka oklahoma

Dec 16, 2003

#1

• Dec 16, 2003

• #1

i would like to know what rpm pills that i should use when using my 125 shot???
with my mods ideally at what rpm do i need to shift out of each gear???
this is my best 3 runs out of 8 runs launching and feathering on crappy good year street tires at 3000rpm and shifting at 6000rpm in each gear:

(1st best)

60ft:------2.213
330ft:-----5.862
1/8th:-----8.881
MPH:------82.07
1000FT:---11.469
1/4:-------13.652
MPH:------103.71

(2nd best)

60ft:------2.247
330ft:-----5.920
1/8th:-----8.931
MPH:------82.28
1000FT:---11.518
1/4:-------13.692
MPH:------104.13

(3rd best)

60ft:------2.184
330ft:-----5.899
1/8th:-----8.940
MPH:------81.61
1000FT:---11.539
1/4:-------13.741
MPH:------102.92

tell me what i can do to possible get more out of it N/A?

 

0

02 blk GT

Founding Member

Oct 27, 2002

132

0

0

Houston TX

Dec 17, 2003

#2

• Dec 17, 2003

• #2

What mods do you have? I say a 3000 and a 5800 pills. Shifting at 6000rpms is fine. I say get some better tires(DR's) and get those 60' times down and pull some low 13's.

Brando

 

96mustang_james

Member

May 20, 2003

199

1

17

atoka oklahoma

Dec 17, 2003

#3

• Dec 17, 2003

• #3

mods are in sig. except for now i have a diablo delta chip and 4.10's that i am going to install in a few weeks. i am hoping to see a 12.99999999 on draglites with m/t et drag slicks. and 11.9999999 with 125 shot.

 

BO94ZA4

Member

Jul 3, 2003

364

0

17

Vance AL

Dec 17, 2003

#4

• Dec 17, 2003

• #4

I have a bud that has a 97 gt I modded for him and w/ 4.10's, shorty headers,x pipe, flows, FIPK, Ripper, and NOS kit set on 120 shot and 28x9 slicks runs 11.90's in the 1/4 and 7.70's in the 1/8 w/ a 1.55 60 ft using 3000/6000 chips in the rpm activated window switch, shifting the car with the shift light set at 5800.

 

96mustang_james

Member

May 20, 2003

199

1

17

atoka oklahoma

Dec 17, 2003

#5

• Dec 17, 2003

• #5

BO94ZA4 said:

I have a bud that has a 97 gt I modded for him and w/ 4.10's, shorty headers,x pipe, flows, FIPK, Ripper, and NOS kit set on 120 shot and 28x9 slicks runs 11.90's in the 1/4 and 7.70's in the 1/8 w/ a 1.55 60 ft using 3000/6000 chips in the rpm activated window switch, shifting the car with the shift light set at 5800.

Click to expand...

does he have the pi headswap done also???

 

BO94ZA4

Member

Jul 3, 2003

364

0

17

Vance AL

Dec 17, 2003

#6

• Dec 17, 2003

• #6

Negative, the engine is stone stock-non-PI.

 

96mustang_james

Member

May 20, 2003

199

1

17

atoka oklahoma

Dec 17, 2003

#7

• Dec 17, 2003

• #7

i hope i can pull off a 11.90, that is my goal.

BTW, all of the passes i was spinning through 1st, 2nd, and part of third gear.

 

D

DC-GT

New Member

Nov 25, 2003

312

0

0

Dec 17, 2003

#8

• Dec 17, 2003

• #8

96mustang_james said:

i hope i can pull off a 11.90, that is my goal.

BTW, all of the passes i was spinning through 1st, 2nd, and part of third gear.

Click to expand...

Too much spinning, look at tires. If you are hooking up better though, you might want to weld your tq boxes.

Bo

 

96mustang_james

Member

May 20, 2003

199

1

17

atoka oklahoma

Dec 17, 2003

#9

• Dec 17, 2003

• #9

i am going to have that done along with my welding my axle tubes also, and i am also getting my rear end spooled with 33 spline axles before i make a pass on slicks.