• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Explorer EGR Valve

  • Thread starter Thread starter 89StAngerlx
  • Start date Start date Aug 4, 2008
8

89StAngerlx

New Member
Nov 19, 2007
19
0
2
Aug 4, 2008
#1
  • Aug 4, 2008
  • #1
When I got the car it had already had the Explorer Intakes on it and today I noticed that it has what I'm guessing is the EGR valve from the Explorer as well. My question is, would this cause my computer to be throwing out a code 34?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 4, 2008
#2
  • Aug 4, 2008
  • #2
I have used the Explorer EGR and it did not set code 34.

Code 34 Or 334 - EGR voltage above closed limit - Failed sensor, carbon between EGR pintle valve and seat holding the valve off its seat. Remove the EGR valve and clean it with carbon remover. Prior to re-installing see if you can blow air through the flange side of the EGR by mouth. If it leaks, there is carbon stuck on the pintle valve seat, replace the EGR valve ($85-$95).

If the blow by test passes, and you have replaced the sensor, then you have electrical ground problems. Check the resistance between the black/white wire on the MAP/BARO sensor and then the black/white wire on the EGR and the same wire on the TPS. It should be less than 1.5 ohm. Next check the resistance between the black/white wire and the negative battery post. It should be less than 1.5 ohm.

Note that all resistance tests must be done with power off. Measuring resistance with a circuit powered on will give false readings and possibly damage the meter.

Let’s put on our Inspector Gadget propeller head beanies and think about how this works:
The EGR sensor is a variable resistor with ground on one leg and Vref (5 volts) on the other. Its’ resistance ranges from 4000 to 5500 Ohms measured between Vref & ground, depending on the sensor. The center connection of the variable resistor is the slider that moves in response to the amount of vacuum applied. The slider has some minimum value of resistance greater than 100 ohms so that the computer always sees a voltage present at its’ input. If the value was 0 ohms, there would be no voltage output. Then the computer would not be able to distinguish between a properly functioning sensor and one that had a broken wire or bad connection. The EGR I have in hand reads 700 Ohms between the slider (EPV) and ground (SIG RTN) at rest with no vacuum applied. The EGR valve or sensor may cause the voltage to be above closed limits due to the manufacturing tolerances that cause the EGR sensor to rest at a higher position than it should.

The following sensors are connected to the white 10 pin connector (salt & pepper engine harness connectors)


This will affect idle quality by diluting the intake air charge


Late Model Restoration has the Ford Racing M-12071-N302 kit with the EGR valve & sensor along with the ACT & ECT sensors for $45. See http://www.latemodelrestoration.com/iwwida.pvx?;item?item_no=M12071N302 1&comp=LRS for more details
 
8

89StAngerlx

New Member
Nov 19, 2007
19
0
2
Aug 4, 2008
#3
  • Aug 4, 2008
  • #3
Thanks. I had read all that other info but then I noticed that was a newer EGR and just wanted to make sure it wasn't some how messing with anything.
 
You must log in or register to reply here.

Similar threads

Engine 1988 Ford Mustang throwing 2 OBD-1 codes (32 and 63) rough cold start and initial idle
  • mikeah
  • Today at 12:38 PM
  • Fox 5.0 Mustang Tech
Replies
1
Views
30
Fox 5.0 Mustang Tech 41 minutes ago
AeroCoupe
Engine Catch Can or not?
  • R82148V
  • Mar 4, 2026
  • Fox 5.0 Mustang Tech
Replies
9
Views
493
Fox 5.0 Mustang Tech Mar 6, 2026
ctandc
C
Engine (EGR Deleted) Solution the hotter combustion chambers?
  • PonyGTrider
  • Jan 21, 2026
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
97
Views
5K
Fox 5.0 Mustang Tech May 2, 2026
PonyGTrider
Engine Vacc leak detector
  • Creomod
  • Jul 19, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
217
Fox 5.0 Mustang Tech Jul 25, 2026
Mustang5L5
D
Question about EGR valve, replacement, and a part on the valve.
  • DPP
  • May 9, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
270
SN95 V6 Mustang Tech May 23, 2026
DPP
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?