• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

head gasket or intake

  • Thread starter Thread starter 94_mustang_gt
  • Start date Start date Jul 24, 2006
9

94_mustang_gt

New Member
May 27, 2006
5
0
0
Jul 24, 2006
#1
  • Jul 24, 2006
  • #1
ok well i just replaced a head gasket on my 90 mustang gt and i got it all put together drove it alittle no problem then all the sudden it started overheating i shut it off and let it cool down took the radiator cap off and started it and when it warmed up it started blowing water out of the radiator what do you guys think???? could it be the other head gasket or lower intake
 

millhouse

Founding Member
May 14, 2002
1,985
0
46
Simpsonville, SC
Jul 24, 2006
#2
  • Jul 24, 2006
  • #2
It sounds as if you put one or both head gaskets on backwards. Did you pay attention to the "front" stamped into the gasket?
 
9

94_mustang_gt

New Member
May 27, 2006
5
0
0
Jul 25, 2006
#3
  • Jul 25, 2006
  • #3
well i pulled my head off and there was atf sittin in the #8 cylinder but i don't see anything wrong with the head gasket and can't find any cracks i dunno what i should do now?
 

dastang2

Active Member
Dec 11, 2003
2,020
0
46
tx
Jul 25, 2006
#4
  • Jul 25, 2006
  • #4
transmission fluid in the motor, did you notice any white heavy smoke through the pipes. you should have. how did that get in there. hope it wasn't just a air bubble in the system because if it was, you just wasted time and money taking it back apart
 
9

94_mustang_gt

New Member
May 27, 2006
5
0
0
Jul 26, 2006
#5
  • Jul 26, 2006
  • #5
no it wasn't just air bubbles i tryed to get all the air out but it don't work and it wasn't bubbling it was spraying water out the radiator everytime it was on a compression stroke but there are no cracks that i can see ane the gaskets weren't cracked or anything so i dunno what it would be unless the intake gasket didn't seal up i dunno
 

donsbad68

Immensely Educated
Jan 4, 2003
838
0
0
Oklahoma
Jul 26, 2006
#6
  • Jul 26, 2006
  • #6
head gaskets backwards? the cooling holes always go in the back
 
9

94_mustang_gt

New Member
May 27, 2006
5
0
0
Jul 26, 2006
#7
  • Jul 26, 2006
  • #7
well i bought felpro's and it has front stamped on one side then you flip it over and its stamped on the other side the opposite end
 
You must log in or register to reply here.

Similar threads

B
99 mustang gt 4.6 excess cooling system pressure
  • Blackbeauty99-4.6
  • Nov 11, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
85
SN95 4.6L Mustang Tech Yesterday at 12:47 PM
Mustang5L5
Engine Catch Can or not?
  • R82148V
  • Mar 4, 2026
  • Fox 5.0 Mustang Tech
Replies
9
Views
510
Fox 5.0 Mustang Tech Mar 6, 2026
ctandc
C
Engine Coolant boiling in hose?
  • Teen'93stang5.0
  • Jun 3, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
357
Fox 5.0 Mustang Tech Jun 8, 2026
Mustang5L5
Fox Help
  • 93fox85
  • Mar 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
332
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 23, 2026
Noobz347
K
Resolved Need some assistance. Holley Terminator X alongside H/C/I. Very rough/inconsistent idle
  • karhoot
  • Jun 6, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
240
Fox 5.0 Mustang Tech Jun 6, 2026
karhoot
K
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?