• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

How much oil for my stang?

  • Thread starter Thread starter ItsStock02
  • Start date Start date Jan 22, 2009
Prev
  • 1
  • 2
First Prev 2 of 2

bhuff30

Founding Member
Dec 11, 2001
6,037
35
129
Olathe KS
Jan 22, 2009
#21
  • Jan 22, 2009
  • #21
I've never lifted the car into the air to change the oil, and I would certainly never use ramps. They just look scary compared to a set of sturdy and well placed jack stands. I've never had a problem leaving the car on the ground and using extensions to access the drain plug and crawling under just the nose to get to the filter.

My 97 takes 6 quarts and states that in the manual. After adding 6 quarts, and starting the engine to fill the oil filter, the dipstick reads correctly. Always remember to run the engine a little to fill the new oil filter before checking the dipstick.

As for mixing synthetic oils, what do you think the blends that are commonly sold are? They are just that, a mix of conventional and synthetic. You shouldn't need to mix weights, but if you do on accident, it shouldn't be a problem, so long as both are close enough to the specified weight.
 
2

2003_GT

New Member
Nov 5, 2008
69
0
0
Santa Fe, NM
Jan 23, 2009
#22
  • Jan 23, 2009
  • #22
flstang65 said:
I do 5 qts and a can of engine restore.
Click to expand...

Does the engine restore do really work???
 

CobraRed_96_GT

Active Member
May 20, 2006
1,421
4
39
UCSD/La Jolla
Jan 23, 2009
#23
  • Jan 23, 2009
  • #23
The more we post wrong info the worse this problem is going to be. If you know how much your car takes, post up. But please don't say 2v's take this, all of them take this ect...

Mine takes 6
 

squeak93

15 Year Member
Jun 2, 2005
2,279
368
164
Joplin, Missouri
Jan 23, 2009
#24
  • Jan 23, 2009
  • #24
My 98 take 5. My old 04 took almost 6 ( I left it a bit lower on purpose).
 

248a

New Member
Feb 9, 2008
0
0
0
Phoenix, AZ
Jan 23, 2009
#25
  • Jan 23, 2009
  • #25
My 1996 2V takes 6.

I always fill the filter before I put it on the car and I've been running a mix of synthetic and conventional since I got the car, and every filter on my car is a Fram, which makes every mustang guy cringe for whatever reason. It has 167,xxx miles and gets WOT to 5k through 1st and 2nd every other day. Trust me, It'll be fine as long as you don't under or overfill it.

My advice is to put in 5 quarts, check your dipstick and adjust accordingly.

also +1 on everyone that said to buy a floor jack and jack stands. There's always a decent set of the GM Goodwrench brand there, I got a 2 1/2 ton floor jack for like $30...
 

streethorse

15 Year Member
Oct 8, 2005
1,042
6
58
Dallas Texas
Jan 23, 2009
#26
  • Jan 23, 2009
  • #26
I use the 2 jack, 2 stand method.... makes tire rotation, oil change etc
fast and easy......

[/IMG]
 

Jinx

I like cats, cats like me. Cats and I fully agree.
20+ Year Stangneter
Oct 2, 2003
12,166
4,237
223
Cat Country
Jan 23, 2009
#27
  • Jan 23, 2009
  • #27
2003 GT, 6 quarts every time (with filter change)
 
M

mikeyskd

New Member
Oct 29, 2008
2
0
0
Jan 23, 2009
#28
  • Jan 23, 2009
  • #28
Oil

I'm experiencing about 5 3/4 to 6 quarts during an oil change. So far I have about 140k on my car and it runs strong. I seem to have to monitor the oil every two weeks since it is seems as some oil is being burned.

Mike
 

BurningRubber

10 Year Member
Dec 6, 2004
1,865
24
58
Jan 23, 2009
#29
  • Jan 23, 2009
  • #29
2003_GT said:
Does the engine restore do really work???
Click to expand...

No it does not. It's "snake oil" and claims to be the miracle in a can product, but it is not. I would NOT run 1 quart of Restore in place of 1 quart of oil. It is thinner than oil and I don't trust that.

I tried Restore on an older beater truck I had because I was curious aswell. It had 14xxxx on it and smoked like a chimney, lots of ticks from the valvetrain (lovely Mitsubishi motor). Restore did nothing but make the oil thin and easier to slip past the rings and get burnt up.
 
J

JayC

Founding Member
Jul 11, 2000
674
0
17
Southern Indiana
Jan 23, 2009
#30
  • Jan 23, 2009
  • #30
Here's some good info from a former Ford tech, now a well known modular engine builder. After reading this I started running 7 quarts with no problems.

"When at Ford, we ran with clear pans, windowed front covers and cam covers. The oil under high rpms gets slowed in the heads, the front cover and the front of the oil pan.

Front cover?? Oil pan??

As the chain drives the cam system, the oil is trying to get down thru the cover area. Also the area around the front of the pan shares space with the oil pump and pickup tube. Oil is trying to get back to the pan and everything is in the way.

The drain back holes are the same between 2v, 3v and 4v.

Ford conducts a WOT test for 100's of hours.

On the street you don't see consistent 6,500+ runs. On the track, I suggest you add 1 qt. Adding 1 qt does not over fill the pan to the point that the crank or rods run thru it. When at idle, you're 2 qts low anyways."
 

evil281

New Member
Jan 6, 2008
276
0
0
Arizona
Jan 24, 2009
#31
  • Jan 24, 2009
  • #31
5 quarts with filter change
 

04GT

New Member
Oct 8, 2003
284
0
0
Southwest Ohio
Jan 24, 2009
#32
  • Jan 24, 2009
  • #32
streethorse said:
I use the 2 jack, 2 stand method.... makes tire rotation, oil change etc
fast and easy......

[/IMG]
Click to expand...

Mine has always taken 6 qts.

Anybody else think it's nuts to crawl under a car suspended on two jacks?

What do jack stands cost, like $5 each?
 

04GreyGtUSAF

Member
Dec 10, 2007
43
0
7
KS
Jan 24, 2009
#33
  • Jan 24, 2009
  • #33
I know my Manual calls for 6 qts if your doing a filter change also. I like to run 5 1/2 and leave the other 1/2 in the trunk just in case. And always runnin the motorcraft filter.
 

BurningRubber

10 Year Member
Dec 6, 2004
1,865
24
58
Jan 24, 2009
#34
  • Jan 24, 2009
  • #34
I usually add an extra half quart or so in addition to what is called for.

Sometimes I get a wild hair and REALLY run the car hard and every time I do I think about all the oil being on the top end.
 
Prev
  • 1
  • 2
First Prev 2 of 2
You must log in or register to reply here.

Similar threads

S
Oil cooler delete 4v 4.6 1999 cobra mustang
  • sami12
  • Feb 24, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
328
SN95 4.6L Mustang Tech Feb 25, 2026
GOvert
G
B
Engine Strange Noise
  • burntokita
  • May 8, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
403
Fox 5.0 Mustang Tech May 11, 2026
keel
S
CHANGING BRAKE PADS
  • Scwhitten
  • Jun 8, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
20
Views
399
1996 - 2004 SN95 Mustang -General/Talk- Jun 12, 2026
nickyb
P
Weird Voltage & Oil Pressure Gauges
  • PNN
  • May 22, 2026
  • SN95 V6 Mustang Tech
Replies
0
Views
59
SN95 V6 Mustang Tech May 22, 2026
PNN
P
J
Engine Coolant leak from oil filter
  • jr273
  • Mar 26, 2026
  • SN95 4.6L Mustang Tech
Replies
9
Views
267
SN95 4.6L Mustang Tech Mar 31, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?