• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech

How often do you restore? Tried taking my car in for quarters

  • Thread starter Thread starter Chris66
  • Start date Start date Sep 16, 2005
C

Chris66

New Member
Jul 17, 2005
18
0
0
Sep 16, 2005
#1
  • Sep 16, 2005
  • #1
Yesterday I towed my car (66 stang conv't) to the body shop to have new rear quarters put on.

I've talked to the guy about the project a few times, and the this guy was recommended by a good friend of mine.

He looked at the car and said I need new outer fenders for the quarters, no big deal, but I also need new rockers panels. The skins are solid, but he says they must have been used, and were hacked (welded) on the car. So he said order the parts and bring back the car when I have the parts.

So I went back to today to verify the exact parts to order and he said, I was thinking last night, I think you should also replace the floor pans. The floor pans are peppered and have patches. There is a patch under each cowl vent, and there is about 5 patches under the rear seat. Theses patches were pop riveted from the previous over. The floors are solid, I have jumped up and down inside the car to test it out. The owner of the shop said he would could to my house to do the repairs, since it is just welding.

So my question is, I am not sure how often you have to do repairs to the floors and stuff. (I live in Chicago, but will not drive it in the winter). Should I bit the bullet and replace everything now, or should I assume I will have to do repairs in 5-10-15 years from now, so wait until problems arise, or when I need to do another restoration.

Thanks in advance.
 

68 Coop

New Member
Aug 13, 2005
104
0
0
64
Mesquite, NV
yahoo.com
Sep 16, 2005
#2
  • Sep 16, 2005
  • #2
The rust you see is just the tip of the problem. I would, since you can afford to do it, DO IT NOW.
 
C

Chris66

New Member
Jul 17, 2005
18
0
0
Sep 16, 2005
#3
  • Sep 16, 2005
  • #3
Thanks for the reply.

From what I have torn into, the rust was taken care off already. I bought the car from was from an older gent that was trying to do a complete restore on his car. The car is very clean, he replaced all the rusted out pieces. He just started pop riveting everything in place verses welding because of his eye sight
 

65up2d8

Member
Mar 30, 2005
281
0
17
Memphis, TN
Sep 17, 2005
#4
  • Sep 17, 2005
  • #4
Chris66 said:
Thanks for the reply.

From what I have torn into, the rust was taken care off already. I bought the car from was from an older gent that was trying to do a complete restore on his car. The car is very clean, he replaced all the rusted out pieces. He just started pop riveting everything in place verses welding because of his eye sight
Click to expand...

If you are ABSOLUTELY SURE all the rust is gone and you don't care about original looking floorpans, then just have the patch panels welded in and the rivets removed. Notice my emphasis above, however. If you're not 100% certain the rust is 100% gone, then bite the bullet and replace the pans. Think of it this way; rust is cancer as far as metal goes, and it will spread quickly just like cancer. Would you feel confident of your prognosis if you had cancer and the doctor put in "patch" tissue but knew some remnants of the cancer was left behind?
 

Hack

15 Year Member
Mar 23, 2004
1,945
13
69
Minneapolis
Sep 17, 2005
#5
  • Sep 17, 2005
  • #5
It all depends on you. If it were me, I wouldn't replace the floor pans. I'd just wait until they get bad and replace them then. If you have the car apart now, you could grind off the surface rust and POR15 them or something. Or just leave them. It will take quite a while for them to rust out if the car is garaged during the winter and rainy days. You might get by 15 years or more.

I guess some people have to have perfect cars. I'm not that way. I just like to drive them and enjoy them. I find I enjoy a car more when I'm not constantly worrying about it getting a drop of water on it or a door ding.

Spend the money someplace where it will do you more good, rather than dropping it into a money pit.
 
C

Chris66

New Member
Jul 17, 2005
18
0
0
Sep 17, 2005
#6
  • Sep 17, 2005
  • #6
I did wire wheel all the paint off the car and spray Eastwood Rust Encapsulator over all the floor boards. I had posted picture of the floor boards a couple of months ago, and the decision was I could leave them as is.

The other thing I was curious about, if the parts are not prep'd correctly or installed correctly, couldn't I be in a worse position in a couple of years then if I didn't touch anything?
 
D

Doc Voodoo

Founding Member
Mar 2, 2001
257
0
0
57
Conn
Sep 18, 2005
#7
  • Sep 18, 2005
  • #7
Do it once do it right never worry about it again.
 

'69Mach1

New Member
Sep 17, 2005
45
0
0
60
Northern N.J.
Sep 18, 2005
#8
  • Sep 18, 2005
  • #8
"Do it once do it right never worry about it again"
I'm all for that ,my '66 convertible was done 15 year's ago ,floor's ,inner, and outer rocker's ,quater's ,outer wheel housing's ,typical mustang ,I have no problem's with rust ,do it once ,why piecemeal it ,and go back and forth to different rust spot's?
 

70vert

New Member
Dec 31, 2004
722
0
0
Bay Area, CA
Sep 18, 2005
#9
  • Sep 18, 2005
  • #9
My advice having just had this done

I bought the car 16 years ago with rust in the floorpans and aluminum patches to cover them up but no real antirust treatment done. I don't know if the rockers were rusted then but they were when I just had them fixed.

-If the rust is into the rockers or threatening them, DO IT NOW! You don't want the rust to get to the outer rocker, it's harder to replace than the inner.

-If just the bottom, away from corners and from rockers you can probably POR it and postpone it

-Wherever rust is in a corner, it is going to be more expensive because you may end up needing 2 parts or some custom work instead of replacing one floor pan piece

Having said that, it took 15 years to really get into the inner rockers if it wasn't already there before, and I didn't need a full rocker panel replacement. I had some driver's side firewall issues and some corner issues, but the cowl was OK but for some surface rust. Convertible kept garaged but not covered for 10 years or so.

good luck, cross your fingers!
 

Hack

15 Year Member
Mar 23, 2004
1,945
13
69
Minneapolis
Sep 18, 2005
#10
  • Sep 18, 2005
  • #10
Doc Voodoo said:
Do it once do it right never worry about it again.
Click to expand...
No such thing.

Metal rusts. Period.

Edit: well if you live in the desert you might be fine forever.
 
You must log in or register to reply here.

Similar threads

B
Rear quarter window regulator
  • BADAZZOMBIE08
  • Mar 29, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
133
2005 - 2009 Specific Tech Mar 29, 2026
BADAZZOMBIE08
B
D
sad day
  • davecobra2
  • Jul 13, 2026
  • What is it Worth?!?!?
Replies
2
Views
142
What is it Worth?!?!? Jul 22, 2026
davecobra2
D
M
Inheriting (and likely restoration of) a 1965 Mustang
  • miniwheats235
  • Feb 17, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
2
Views
266
1965 - 1973 Classic Mustangs -General/Talk- Feb 19, 2026
Realmongo
S
Car shakes when taking off help???
  • STANKYstangs
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
342
1996 - 2004 SN95 Mustang -General/Talk- May 27, 2026
LILCBRA
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
190
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?