• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Ignition masters, come on in..........

  • Thread starter Thread starter 1993SSP
  • Start date Start date Apr 10, 2008

1993SSP

Founding Member
Sep 5, 2001
1,194
0
37
Ky
Apr 10, 2008
#1
  • Apr 10, 2008
  • #1
Here's a quick summary of my problem:


I had developed a miss at around 3500 rpm's, checked the codes, showed bad 02 sensors, I checked the fuel pressure in the process and I had failed to adjust it after a intake swap, got the fuel where it needed to be, new 02 sensors and the miss seemed to be fixed. Loaded the car up and hauled it for a dyno tune, under load it had a miss during the first run, not near as bad but it was noticeable.

The mallory dizzy I had in the car had a problem and we put a stock dizzy with new cap and rotor button. Problem solved. (so it seemed)

I got the car out today and took it for a drive, it wanted to get a slight miss in it but seemed to clear up after the engine warmed up.

But I noticed when in second gear running 40 mph at around 3000 rpm the tach needle wants to flutter back to about 2200 or so, you can barely notice the miss and when you go to wide open the problem goes away, sooo any suggestions? I have a brand new accel 300+ ignition. The stock dizzy has all brand new Motorcraft internals.

Needless to say, this is starting to drive me insane, possible that it could be the plug wires themselves???
 

RYC CUKR

Founding Member
May 19, 2002
1,437
1
38
Orlando
Apr 10, 2008
#2
  • Apr 10, 2008
  • #2
I had a similar problem a while back and after putting a new dizzy and ignition box in it the problem was still there. It usually went away or at least got better after it was warmed up. Turned out that I had a plug that the gap had somehow gotten closed up on. Regapped the plug and problem solved. Might not be your problem but it is free to check.
 

1993SSP

Founding Member
Sep 5, 2001
1,194
0
37
Ky
Apr 10, 2008
#3
  • Apr 10, 2008
  • #3
Thanks for the reply, new plugs installed and gapped them myself. I'm gonna try the plug wires next
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Apr 10, 2008
#4
  • Apr 10, 2008
  • #4
Another vote for misting the plug wires to see if one is leaking.

Good luck.
 
You must log in or register to reply here.

Similar threads

B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
518
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
J
Lack of power on acceleration
  • jameshernandez
  • Aug 30, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
194
1996 - 2004 SN95 Mustang -General/Talk- Sep 6, 2026
jameshernandez
J
C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
246
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
614
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
593
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?