• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Injector problems, please help

  • Thread starter Thread starter Boss 351
  • Start date Start date Apr 27, 2006
B

Boss 351

Here sthhhhhhhheeeve take a picthh of my man flowe
Jul 13, 2003
2,433
23
48
Canada
Apr 27, 2006
#1
  • Apr 27, 2006
  • #1
Welp I installed my Cobra intake, removed smog air pump and EGR. I let my engine run to heat up to check for coolant leaks (everything fine, no CEL either)...

Now for the problem: The engine runs funny like it's missing a cylinder and I hear a strange ticking noise out the exhaust (on one side only). I remove all the plugs on that side and find 3 out of 4 plugs that are normal and dry but the one on cylinder #7 is soaked in fuel. I checked to see if that cylinder has spark which it does so I suspect the injector is stuck open?

So what are the symptons for a stuck injector? My engine starts up just fine but runs like it's flooded yet there's no black smoke out the tailpipes. Any tips? I know that when I installed that injector, it had a broken plastic retainer so I only crazy glued it?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 28, 2006
#2
  • Apr 28, 2006
  • #2
Fuel pressure OK, the injectors are not firing, OR one or more injectors stuck
open

Do a cylinder balance test: Warm the car's engine up to normal operating
temperature. With the Engine Off, Key OFF, use a jumper wire or paper clip to
put the computer into test mode. Start the engine and let it go through the
normal diagnostic tests, then quickly press the throttle to the floor. The
engine RPM should exceed 2500 RPM's for a brief second. The engine will shut
off power to each injector, one at a time. When it has sequenced through all
8 injectors, it will flash 99 or the number of the failing cylinder such as 22 for
cylinder #2. Quickly pressing the throttle again up to 2500 RPM’s will cause
the test to re-run with smaller qualifying figures. Do it a third time, and if the
same cylinder shows up, the cylinder is weak and isn’t putting out power like
it should. See the Chilton’s Shop manual for the complete test procedure

The red wire on each injector is powered up whenever the ignition switch is
in the Run position. The computer provides a ground to complete the circuit
and fire the injector. The injector must have a ground to squirt fuel on
command. A short to ground in the injector return wiring can cause one or
more injectors to be continually open or triggered
A.) A Noid light available from Autozone, is one way to test
the injector wiring. If the light stays on constantly, either the wiring has a
short to ground or the computer has failed

B.) I like to use an old injector with compressed air applied to the
injector where the fuel rail would normally connect. I hook the whole thing
up, apply compressed air to the injector and stick it in a paper cup of soapy
water. When the engine cranks with the ignition switch on, if the injector
fires, it makes bubbles An injector stuck open will release a continual stream
of bubbles. Cheap if you have the stuff laying around, and works good too.
The same trick works great to find leaking injectors too.​
The wiring for the injectors may have some bare spots in it causing the
injector to computer control wire to ground out. This would cause the
injector to remain on anytime the key was in the Run position. Remove the
injector wiring connectors from the injector. Note that each injector has one
red wire for power and a non red wire (wire some color other than red) for
computer controlled ground. With the key off, disconnect the computer
connector from the computer. Use an Ohmmeter between the non red wire
and ground. You should see more than 100000 (100K) ohms resistance.


See the following website for some help from Tmoss (diagram designer) &
Stang&2Birds (website host) for help




Using the above diagram, check the resistance between the injector and the
computer. Clean and check the 10 pin connectors since they are a potential
trouble source. Any resistance greater than 1 ohm between the injector to
computer wire and the matching pin on the computer connector is a problem.



See http://fordfuelinjection.com/?p=6 for more help

Here's the link to dump the computer codes with only a jumper wire or paper
clip and the check engine light, or test light or voltmeter. You’ll need it to do
the cylinder balance test

See http://www.troublecodes.net/Ford/
OR
See http://www.dalidesign.com/hbook/eectest.html for more descriptive help
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html
 

Attachments

  • 88-91eecPinout.gif
    167.1 KB · Views: 161
B

Boss 351

Here sthhhhhhhheeeve take a picthh of my man flowe
Jul 13, 2003
2,433
23
48
Canada
Apr 28, 2006
#3
  • Apr 28, 2006
  • #3
Thanks I didn't know it used a ground to activate the injector... I'll use my scantool to run an engine on test before removing my upper to see what to look for. But I suspect that injector is grounded and causing it to stay open... I bought a new one anyway.
 

bock

Founding Member
Jan 7, 2002
648
2
19
Montreal,Qc
Apr 28, 2006
#4
  • Apr 28, 2006
  • #4
A simple way to check an injector.

switch it with an other.

if the trouble fallow the injector (wet plug),well its the problem.
 
You must log in or register to reply here.

Similar threads

M
Electrical 93 5.0 No Injector Pulse
  • machinermac
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
15
Views
520
Fox 5.0 Mustang Tech Aug 1, 2026
Willybill32
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
529
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Electrical 88 EEC Injectors batch firing ?
  • Dustin 86GT
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
661
Fox 5.0 Mustang Tech Jan 8, 2026
gkomo
P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
183
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
M
Bad starter?
  • mason5.0
  • Oct 6, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
251
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 6, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?