Just Changed Oil --> Slight Problem Now...

viperos

New Member

May 19, 2003

2,943

0

0

Bellevue, WA (yes, the land where every 16 year o

Feb 5, 2004

#1

• Feb 5, 2004

• #1

well, I changed my oil, didn't take long, put new filter in, all went fine... but when I went to start my car, to check my oil level, I am about 1 qt over the full line... I really don't think I put 6 qts in... but that's what it looks like... any problem with this? I don't really want to have to drain it and refill it with new oil...

-anything wrong with being too full? or should I worry... like every little other thing that isn't perfect on my car

 

P

PRO50SC

New Member

Dec 28, 2003

1,012

1

0

Olney, Maryland

Feb 5, 2004

#2

• Feb 5, 2004

• #2

That full line is on the dipstick for a reason. Drain out the overage.

 

BlueOvalStangGT

Active Member

Oct 27, 2003

2,849

0

46

Tampa Florida....USF!!!

Feb 5, 2004

#3

• Feb 5, 2004

• #3

if you really need too you could just open up the plug quickly and estimate a quart coming out.

 

viperos

New Member

May 19, 2003

2,943

0

0

Bellevue, WA (yes, the land where every 16 year o

Feb 5, 2004

#4

• Feb 5, 2004

• #4

well, I know from experience with my Bronco that you can't easily (cleanly) drain just a bit... so, I think I could just undo one of my plugs, drain it, and fill it up with like 3 qts...

-but it would not be a good idea to just leave it? what's the worst that could happen?

 

Rel

Founding Member

Aug 7, 2002

344

0

0

Los Angeles, California

Feb 5, 2004

#5

• Feb 5, 2004

• #5

Are you removing both drain plugs, or just one? If not chances are you still had a quart of old oil in there when you filled it up.

 

R

rudeone707

New Member

May 17, 2003

1,829

0

0

Fairfield, Ca

Feb 5, 2004

#6

• Feb 5, 2004

• #6

over filling is a

 

Jerry Leaming

Member

Nov 2, 2003

477

2

18

Olympia Wa

Feb 5, 2004

#7

• Feb 5, 2004

• #7

Too much oil can cause the crank to slap the oil when its rotating causing a viberation. Not Good. I have heard that the filter holds about a quart of oil.?
If you ran the car than that might be an idea or just drain out the extra oil.

 

viperos

New Member

May 19, 2003

2,943

0

0

Bellevue, WA (yes, the land where every 16 year o

Feb 5, 2004

#8

• Feb 5, 2004

• #8

yeah... the strange part was after I changed everything (and yes, I did remove both plugs, and drained all the oil) filled it back up and started it, the oil level didn't go down much... like the filter already had oil in it... that's why I have this problem now...

I guess I will go drain the oil then, and fill her up w/ some new stuff...

 

Jerry Leaming

Member

Nov 2, 2003

477

2

18

Olympia Wa

Feb 5, 2004

#9

• Feb 5, 2004

• #9

If you keep the oil clean than there is no reason to put new oil in. Get a CLEAN oil drain pan.. drain the oil and put back in what you need.

 

viperos

New Member

May 19, 2003

2,943

0

0

Bellevue, WA (yes, the land where every 16 year o

Feb 5, 2004

#10

• Feb 5, 2004

• #10

okey dokey... I don't have a clean oil pan, but I guess it never hurts to have two of something...

 

viperos

New Member

May 19, 2003

2,943

0

0

Bellevue, WA (yes, the land where every 16 year o

Feb 6, 2004

#11

• Feb 6, 2004

• #11

well, I went to schucks, they didn't have an oil pan!! and I wasn't about to drive 20 min to get one... so I just drained my oil, and replaced w/ new stuff... (get it cheap at costco anyway... why not?) my oil was dirty actually anyway... so that was ok w/ me... I only drained the front bolt, but I had to replace it w/ 4.5 qts!! I couldn't believe it... and I'm still about .3 qts low of the full line... but it is in the dashed area, so I guess that's fine...