• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Oil pan gaskets

  • Thread starter Thread starter cadeezy1
  • Start date Start date Jun 1, 2007
C

cadeezy1

New Member
Jun 18, 2006
1
0
2
Jun 1, 2007
#1
  • Jun 1, 2007
  • #1
does any body have the steps for changing oil pan gaskets? I've looked around and it's not even in my shop manuals.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 1, 2007
#2
  • Jun 1, 2007
  • #2
The following is for an oil pump, but the steps are the same.

Been there, done that - You can do it in the car, but it is hard to do. The best way is to pull the engine.

Disconnect the battery at the battery ground terminal, remove the fan and fan shroud. Both motor mounts will need to have the large nuts that secure them to the frame removed. The trans mount will also have to be loosened, and it is a good idea to remove the drive shaft.

I also had to disconnect the cat pipes at the headers to get the engine high enough to remove the oil pan. Be prepared to have to drop the steering rack and disconnect the steering shaft. Jack up the engine with a wood block under the oil pan and watch for things that bind or hoses/electrical wiring that may need to be disconnected. I put a couple of wood blocks between the headers and the frame to support the engine. You will likely need to jack up the rear of the transmission as well to get the required clearance.

Scrape the pan mating surfaces clean as possible - old gasket stuck to the surfaces are a source of leaks.

Get a high volume/heavy duty pump, and a replacement HD pump shaft. FMS makes one, and ARP does too. When you install the pump, the funny looking washer thingy goes on the part of the shaft that fits into the hex socket in the distributor shaft. It keeps the shaft in place when you remove the distributor, which you will have to do to prime the pump. Forget to put it on, and the pump shaft can come loose and fall down in the bottom of the oil pan.

There is a one piece oil pan gasket which will help re-assembly if you can find it. If you can't get this gasket, use weather strip adhesive to secure the cork gasket to the pan rails and the rubber strips to the bearing caps. Use lots of Acetone or MEK to clean the gasket surfaces so the weather strip adhesive will stick good. Read the instructions on the adhesive carefully to make sure the gaskets are permanently stuck in place and won't move when you slide the pan in place. Use lots of blue silicone sealer on top of the front and rear rubber seals where they mate with the pan.

Fill with oil, replace the filter. Reconnect the battery, switch the ignition on to enable the gages, but DON'T crank the car. Remove the distributor and use a 1/4" hex socket to turn the pump counter clock wise (same direction as distributor rotation) until you see oil pressure (an external gage is a great help long about now). And keep turning for about 30 sec after you see the pressure come up. A reversible drill is the best tool to use to turn the 1/4" socket. The pressure should come up to about 50-80psi with cold oil. Once you see good pressure, check for obvious leaks, and then and only then, lower everything back into place and bolt down the mounts and anything else you had to take loose.

Re-install the distributor and set the timing with the engine running using timing light (don't forget to disconnect the SPOUT plug and reconnect it when finished) 12-14 degrees BDC is good. Start up and check for leaks, let it warm up and look again for leaks. It took me 2 days plus, but I am old and slow, maybe your granny is faster.
 
You must log in or register to reply here.

Similar threads

S
Mustang 2 74’ Oil Pan Help
  • scaryfresh
  • Aug 12, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
1
Views
131
1974 - 1978 Mustang II Talk & Tech Aug 12, 2026
LILCBRA
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
Help Identifying Engine Harness Plug
  • FoxbodyRob
  • Feb 7, 2026
  • 2.3L (N/A & Turbo) Tech
Replies
3
Views
330
2.3L (N/A & Turbo) Tech Feb 7, 2026
FoxbodyRob
W
Dipstick
  • wccurtis1963
  • Jun 13, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
274
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
Willybill32
B
Engine Strange Noise
  • burntokita
  • May 8, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
565
Fox 5.0 Mustang Tech May 11, 2026
keel
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?