• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

P to V clearance

  • Thread starter Thread starter stevesLX
  • Start date Start date May 2, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
May 2, 2007
#1
  • May 2, 2007
  • #1
So I am going to pull my heads tonight. I am just curious if I see any evidence that I have P to V clearance how do I determine whether I need new heads or a new block. Both of mine have been cut on both the heads and the block. I really hate to have to replace the block ecspecially since I just had it freshened up back in January and have less than 2000 miles on it. I am still having all the sewing machine noise and I have replaced or eliminated everything else. So I figure I will pull the heads and see if I cant see any marks from the valves hitting the pistons. I had one guy tell me that I should be running quicker than a 14.10 in a quarter. He claims to have had a stock 302 foxbody and running 13.50's all day long with street tires. And I have mods done to mine. Mine has edelbrock 5.0 performer intake, F cam, 24# injectors, 255 holley FP, 75MM TB, 73MM MAF, aluminum drive shaft. I have yet to get a tune or chip for any of the mods yet though. So if he's running 13.50's bone stock and I am running 14's with mods than somethings not right. I personally think the car runs alright just that damn noise.
 

Mr Grim

New Member
Dec 29, 2006
58
0
0
May 2, 2007
#2
  • May 2, 2007
  • #2
14.10 sounds just about right. Your buddy running 13.5 on stock either has gutted his car down to nothing, or was running in perfect air/conditions, or isn't being completely honest about his time/mods.....or all of the above. My best 1/4 so far running stock (except for headers and an off-road x-pipe) is 14.90 with stock 3.08 gears and street tires....crappy 60' (2.3) , 3420 lbs, at 5,187' alt.
It kills me why some people have to lie about their times.... Then when when you watch 'em run at the track some mysterious gremlin adds 1 1/2 seconds on to their runs!
Are you running roller rockers? ...That "sewing machine" sound is pretty normal for RR's.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
May 2, 2007
#3
  • May 2, 2007
  • #3
no I have stock steel ford factory rockers on it. And I have replaced 2 sets of lifters now. I have replaced the factory springs with cranes beehives that support up to 540 lift. The cam I have is a F cam and its onley 512 lift. Now with that being said I have made sure the springs and the retainers aren't hitting the rockers anywhere both when the vale is open or closed. The whole kicker to this is I took my block and heads to the machine shop in January to have the block freshened up because I had blow by. The rings were history. So they cleaned up my block pistons rods crank and cam. They replaced the rings seals plugs and bearings with all new also the sprockets and timing chain. Now I gave them my heads also. These are stock heads. They took off around 5-7 thousandths on my heads and replaced the seals and did a 3 angle valve job. I picked up my heads and block from them. I put the heads back on the block and dropped it back in the car put everything else together and walla the car sounds like absolute crap unless its sitting still and just idleing. Before I took the motor out I had none of these issues. I would have rather of had to deal with the blow by then the way this thing sounds. When I replaced the last set of lifters I left the intake off and used a length checking push rod on every single lifter and my preload is anywhere from .040-.050 on all of them. So other than all of them not being dead nuts at one particular preload they are all in the specs. So I start the car and it doesn't sound any differen't. I have ruled out header leaks also. It is definitely motor. Now the machine shop swears I dont have P to V issues but yet they called me when they had my block and said someone has really cut down on the deck height and they said my pistons were coming up .015 out of the hole and that they would have to notch my pistons or something and they wanted to know how thick of a head gasket was on ther when I took it apart. Which I didn't know I took it off and threw it in the trash. But I dont know what else to do at this point. I know the car seems to run alright like I said at a temperature of 190 degrees she ran 14.151 with street tires. I have also srayed it with a 75 shot yestar day and the day before and other than chattering a little louder nothing else as of yet seemed abnormal. I just want to fix it before it gets worse or I screw something up.
 

88mouse

New Member
Apr 18, 2007
630
0
0
Mooresville nc
May 2, 2007
#4
  • May 2, 2007
  • #4
I don't think you piston to valve clearnce is you proablem.I have a TFS 1 cam with 1.7RR and my heads were shaved 30 thousands. Do you have any valve lash?I had to shim my 1.7's because I had to much valve lash.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
May 2, 2007
#5
  • May 2, 2007
  • #5
The ratio I have is 1.6. I dont think I understand what you mean by valve lash. The way I set this up was I put the second set of new lifters in and I went down thru the fireing order top dead center and I inserted my length checking pushrod and threaded it out until it was up into the seat of the rocker and just as the lifters plunger would start to pushin I would stop unthreading the rod and remove it measure it with a caliper and add.040 and then I used the appropriate push rods. Now like I said these are 1.6 factory steel non adjustable rockers. I was getting anwhere from a 1/2 to 3/4 turn out of each one to torque specs. I have tried every oil on the market thick thin and also even risolone and nothing helps.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
May 2, 2007
#6
  • May 2, 2007
  • #6
Any ideas before I go thru the hassle of pulling these heads off tonight?
 

88mouse

New Member
Apr 18, 2007
630
0
0
Mooresville nc
May 2, 2007
#7
  • May 2, 2007
  • #7
aight Turn you motor over untill witch ever clyinder u want to check first is on TDC. Then look where the tip of the rocker and the tip of the valve is see if there is any space there. If so that would be your valve lash. If you have any there you will need to take the rocker of and grind some of the pedestal off,or find a set that is shorter than yours. I will attach a pic to show you what im talking about it is the little pedestal that looks like a T. They make different size ones. The ones that came with my 1.7 were to tall and i just happen to have a shorter set on a set of 1.6 that i had so i just swaped them.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
May 4, 2007
#8
  • May 4, 2007
  • #8
O.K. guys I tore my heads off last night and there is nothing that indicates that I have any valves that have been hitting pistons. So I dont know what to do now. I even took my heads to another machine shop today and they tore them apart and checked everything on them and they are fine. So I am at a lost now as to what is causing me all this racket. Just to make sure I didn't overlook anything I went out and bought a length checking pushrod and last week when I put my 3rd set of lifters in I went thru every single one with the checking push rod and unscrewed it to 0 lash and added .040 on to it and still came up with the same as I did before I bought the checking rod
 
You must log in or register to reply here.

Similar threads

D
Exhaust Difficulty of fixing exhaust leak at manifold
  • dqureshi06
  • Aug 27, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
352
Fox 5.0 Mustang Tech Aug 28, 2026
General karthief
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
1
Clearance
  • 1993mustang50
  • Apr 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
229
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 4, 2026
2000xp8
G
Electrical Getting good ground in 1991 Fox Vert for amps - getting popping noise when I turn on the lights?
  • gvanginkel403
  • Apr 11, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
20
Views
880
Fox 5.0 Mustang Tech Jul 21, 2026
gvanginkel403
G
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
320
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?