• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Pressure gauge adapter

  • Thread starter Thread starter LaserSVT
  • Start date Start date Jun 29, 2007

LaserSVT

Got FB banned again for saying nards
Founding Member
Nov 29, 1999
9,402
3,548
233
Jun 29, 2007
#1
  • Jun 29, 2007
  • #1
Anybody know where I can get an adapter to fit a fuel pressure sending unit to the schrader valve?
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Jun 30, 2007
#2
  • Jun 30, 2007
  • #2
HA! good luck finding that sh:t...i just checked EVERYWHERE and couldn't find it anywhere locally. you can order it from summit though.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 30, 2007
#3
  • Jun 30, 2007
  • #3
What size is your sender? I was able to get the AM adapter for 6 bucks from the local hot rod shop.
Now I did choose to get the AN to pipe thread adapter online but a hot rod shop might have had it too.

JRichker has a neat little write-up with some part numbers and thread sizes if you need it.

Good luck.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 30, 2007
#4
  • Jun 30, 2007
  • #4
Fuel pressure gauge adapter fittings:
http://www.holley.com/products.asp?product=17945NOS AN 4 to 1/16” pipe
http://www.holley.com/products.asp?product=16785NOS 1/16” male pipe to 1/8” female pipe

Or
See http://www.autometer.com/cat_accessorieslist.aspx?pid=10

I made my own pressure gauge and holder. I bought the NOS or Autometer adapter that you screw into the place on the fuel line where the schrader valve goes. You have to remove the Schrader valve, but save it, since you will reuse it. I ran a piece of SS (stainless steel) braided hose to a 1/8” pipe brass tee fitting that I mounted on the fender well by the MAF. I made a mount bracket out of aluminum angle I got from Home depot and bolted it to the fender well. Then I mounted the brass tee to it with some machine screws and a plate. I sandwiched the brass tee between the aluminum angle and a flat piece of aluminum that I trimmed off the extra aluminum angle. Three screws laid out in a triangle pattern go through both pieces of aluminum to clamp the tee in place. Put the Schrader valve in the spare port of the brass tee. I used a cheap industrial gauge from MSC Direct (http://www1.mscdirect.com/ P/N 56468499). It works great and was cheaper than (less than $6) anything Summit had.

If you look through the MSC Direct catalog, you can find any type of gauge you want, including liquid filled. You only need a liquid filled gauge if you mount it directly on the engine. The liquid filling dampens out the vibrations.

You can buy the Autometer Stainless Steel braided hose for like $60. Or a local shop that makes hydraulic hose assemblies can make it for you at a cheaper price. Ordinary low pressure hydraulic hose can be used in place of the Stainless Steel braided hose, the Stainless Steel braided hose just looks nice. I got mine for $4 at a place that sells industrial and military surplus parts of all kinds. The Stainless Steel braided hose goes for about $3.60 a foot and the fittings are probably about $5-$8 each. You can make your own and save some $$$, the shops may have a setup or labor charge to fabricate the hose assembly.









 

LaserSVT

Got FB banned again for saying nards
Founding Member
Nov 29, 1999
9,402
3,548
233
Jun 30, 2007
#5
  • Jun 30, 2007
  • #5
Turns out Autometer makes them (1/16th to 1/8th) and the number is 3280. Autozone can get them, not normal stock. 50Resto has them in stock for $10. When my hood comes in next week I will go down to Waco and get one, I just wanted to play with it now.
 
You must log in or register to reply here.

Similar threads

J
Having fuel issues
  • Jbands2v
  • Nov 2, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
80
SN95 4.6L Mustang Tech Nov 2, 2026
LILCBRA
Need help ordering a oil cooler and filter relocation kit but don't know what I need
  • Aiden Brown
  • Aug 22, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
119
SN95 4.6L Mustang Tech Sep 14, 2026
squeak93
B
Fuel 1990 installing edelBrock intake
  • Beaker
  • Oct 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
348
Fox 5.0 Mustang Tech Oct 6, 2026
Noobz347
M
05 Mustang GT With Annoying P0463 Issue
  • Machbud
  • Oct 17, 2026
  • 2005 - 2009 Specific Tech
Replies
2
Views
192
2005 - 2009 Specific Tech Oct 24, 2026
manicmechanic007
C
Looking for electrical schematic 1986 GT
  • CMT3
  • Sep 21, 2026
  • The Welcome Wagon
Replies
3
Views
175
The Welcome Wagon Sep 23, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?