Progress Thread The "grátis" 1966 Coupe

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
The inner portion of the inner rocker does have some damage with a bit of an outward bow. Might it be a good idea to cut some of the outer rocker out just so I can get a hammer in there and get the inner rocker flat again?
 
  • Sponsors(?)


02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
I'm thinking it may just pull together fine since it's not sitting flat on the humps at the moment. We'll see. I'm going to take it back out to drill and punch holes.
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
So I need advice. I don't think I can proceed with the floor until I fix this. I straightened out the pinch weld on the bottom of the rocker so I could get a better feel for what state it's in.

The inner rocker is bent inward at the bottom.
5xR6lxj.jpg


The top of the inner rocker is straight.
0XgIHzw.jpg


Here you can see where it is bent inward (not outward as I originally though) on the inside. This is where it is bent the most.
QNDgwSz.jpg


@horse sence Here's where I need the advice. I think it may be possible to remove a section of the outer rocker and get the inner portion flat again. Remove the outer rocker, get the inner flat, and the new outer should help maintain the correct shape? If this is possible, what do I need to brace/support to do this? The rear frame rails aren't yet supported. I need to get a set of taller jack stands for that.

Or would you recommend replacing the entire rocker? If so, what do I need to do to brace the car for that?
 

horse sence

That $5 hooker turn out to be a guy
Mod Dude
Nov 29, 1999
9,148
3,583
233
Wile Coyote's stunt double
Once you cut the outer rocker off you should be able to knock around the inner plate . When you clamp the inner to the new outer it should straighten the inner . I have some braces you could easily copy to brace the front to the rear ,i will get some pics
 
Last edited:

horse sence

That $5 hooker turn out to be a guy
Mod Dude
Nov 29, 1999
9,148
3,583
233
Wile Coyote's stunt double
So I need advice. I don't think I can proceed with the floor until I fix this. I straightened out the pinch weld on the bottom of the rocker so I could get a better feel for what state it's in.

The inner rocker is bent inward at the bottom.
5xR6lxj.jpg


The top of the inner rocker is straight.
0XgIHzw.jpg


Here you can see where it is bent inward (not outward as I originally though) on the inside. This is where it is bent the most.
QNDgwSz.jpg


@horse sence Here's where I need the advice. I think it may be possible to remove a section of the outer rocker and get the inner portion flat again. Remove the outer rocker, get the inner flat, and the new outer should help maintain the correct shape? If this is possible, what do I need to brace/support to do this? The rear frame rails aren't yet supported. I need to get a set of taller jack stands for that.

Or would you recommend replacing the entire rocker? If so, what do I need to do to brace the car for that?
Someone ran that side up on somthing ,all those holes were for beating the rocker out again .if you block that side up well you could remove the whole outer rocker . Problem is ,the rear door post is attached to the rocker so it has to be drilled loose so you will need front to back bracing and side to side bracing . I have done a whole side before ,as long as you take measurements of everything and support it and brace it well it isnt to hard to do
 

horse sence

That $5 hooker turn out to be a guy
Mod Dude
Nov 29, 1999
9,148
3,583
233
Wile Coyote's stunt double
The new rockers have the front extensin made to them ,if the original is in good shape i would leave that and cut the new rocker where it will over lap the old extension ,that will help align the rocker and save some removal
 
  • Like
Reactions: 02 281 GT

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
I would only remove the whole outer and leave the inner in place ,that will help keep things in line
That's what I was hoping you'd say. I'd like to do a partial patch like you did on your fastback conversion sticky thread. This way I won't have to mess with the door post(s).

The floor pan is prepped except for needing holes drilled on the front and rear where it meets the firewall and transition pan. Don't mind the weld-thru primer. It's just there for rust prevention since the rocker panel is taking priority.
SghWXWI.jpg
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
So I’m thinking I’ll remove the outer rocker, bend the inner more or less flat and then hammer it out. I need to make one of those braces you have.
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
@horse sence Do I need any extra bracing to replace the tops of the rear torque boxes? Figured I’d go ahead and do that since they came with the floor pan.
 

horse sence

That $5 hooker turn out to be a guy
Mod Dude
Nov 29, 1999
9,148
3,583
233
Wile Coyote's stunt double
If they are not bad i would leave them . As long as you have the rear rails level and supported you should be able to replace them if needed . I have a whole collection of those top here that i didnt need to replace
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
If they are not bad i would leave them . As long as you have the rear rails level and supported you should be able to replace them if needed . I have a whole collection of those top here that i didnt need to replace
The driver's side one is fine. The passenger side is solid, but has a lot of pitting from surface rust. The rear passenger side foot well had the most rust.
DSC_1309.JPG
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
Floor pan prep is complete.
vOrSMPC.jpg


Also got the car 100% level with the rear frame rails supported. I bought some taller 6 ton jack stands just for the task.
A7lZVip.jpg

T3ATq9n.jpg


I didn't do much today. Other than finishing drilling on the floor pan, I hammer and dollied the rear seat divider area. If you go back and look you'll see that both sides were bent inward. They're nice and flat now. Also fixed some bends in the seat back frame.
lfBfZIX.jpg

MD9hFMW.jpg


I went ahead and put the floor pan in the car to get it out of the garage. The gaps were better this time for some reason. I don't think it'll be too difficult to fit it correctly once I repair the rocker. Thankfully all the holes I drilled for the floor supports and frame rails were all spot on!
w3YlDKi.jpg

vxATI4E.jpg

EmKmPlT.jpg

rdoRZqt.jpg

ljQvezq.jpg

9w4EqhB.jpg

701yZ5J.jpg


Almost starting to look like a car again!
AuavbQu.jpg
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
I just realized I forgot to drill holes for where it will be welded to the rear torque boxes.
 

02 281 GT

Agreed...My wife has great Boobs
10 Year Member
Feb 3, 2009
2,231
1,355
174
Cabot, AR
@horse sence Another quick question: would I be OK to remove the lower cowl with the car supported front to back and level? I wanted to address surface rust issues in that area and get it back together.
 
Thread starter Similar threads Forum Replies Date
A 1966 i6 steering/suspension help 1965 - 1973 Classic Mustangs -General/Talk- 5
R Can someone tell me Approximate Build date from Vin production # on my 1966 2+2? 1965 - 1973 Classic Mustangs -General/Talk- 1
H over heating on 1966 mustang Classic Mustang Specific Tech 3
A Engine Need Help Finding a Part Classic Mustang Specific Tech 1
R 1966 Mustang Coupe Wiring 1965 - 1973 Classic Mustangs -General/Talk- 2
R 1966 Mustang Brake Issues 1965 - 1973 Classic Mustangs -General/Talk- 9
R 1966 Coupe Radio Wiring 1965 - 1973 Classic Mustangs -General/Talk- 0
A 1966 Coupe Slow Build 1965 - 1973 Classic Mustangs -General/Talk- 21
N Need Help With 1966 Mustang Heater Problem Classic Mustang Specific Tech 8
R 1966 Coupe Wiring Question 1965 - 1973 Classic Mustangs -General/Talk- 0
S Thermal clutch fan recommendations for 1966 Mustang w/ 289 1965 - 1973 Classic Mustangs -General/Talk- 1
6 Biggest rear tire stock height 1966 Mustang??? 1965 - 1973 Classic Mustangs -General/Talk- 0
M Will a Mustang radio made for a 1964 - 1966 Mustang Stereo 1965 - 1973 Classic Mustangs -General/Talk- 7
R 1966 1965 - 1973 Classic Mustangs -General/Talk- 2
wicked93gs 1966 Mustang Coupe: Ford 3.7L swap 1965 - 1973 Classic Mustangs -General/Talk- 10
Z building a 1966 mustang straight 6 200ci on a budget Classic Mustang Specific Tech 3
M In Tank Pump for 1966 EFI Conversion-1973 tank? Classic Mustang Specific Tech 2
wicked93gs Offbeat project: 1966 Coupe 1965 - 1973 Classic Mustangs -General/Talk- 4
wicked93gs Swapping a 3.7L v6 into my 1966 Mustang, looking for a bit of ECU info 2005 - 2014 Specific V6 Tech 10
S WTB/Trade Need AC unit for 1966 Mustang convertible Interior Exterior Parts 0
M Questions about putting a 4.6 into a 1966 1965 - 1973 Classic Mustangs -General/Talk- 28
B 1966 289 Mustang Overheating 1965 - 1973 Classic Mustangs -General/Talk- 8
S Engine 1966 Mustand straight 6 Classic Mustang Specific Tech 3
W 1966 mustang 289 Balance mystery Classic Mustang Specific Tech 10
N 1966 mustang rear axle 1965 - 1973 Classic Mustangs -General/Talk- 2
R My new 66 mustang 1965 - 1973 Classic Mustangs -General/Talk- 5
D 1966 carpet color 1965 - 1973 Classic Mustangs -General/Talk- 4
K For Sale Translucent Red 1966 Ford Mustang GT350 For Sale! Classic Mustangs For Sale 0
S 1966 neutral safety switch vs transmission issue? Classic Mustang Specific Tech 3
R For Sale Classic 1965GT 1966 Mustang gauges Interior Exterior Parts 0
S 1966 Shelby 10 spoke wheels. Real? 1965 - 1973 Classic Mustangs -General/Talk- 4
S New 1966 fastback owner! The Welcome Wagon 6
S 1966 Mustang thermactor filter 1965 - 1973 Classic Mustangs -General/Talk- 4
robthechemist Excited to join! New Guy in California- 1966 coupe/ 302 swap- 4 speed toploader The Welcome Wagon 13
VOORHEES Family owned 1966 C-code Fastback soon to be out for restoration. PICS ADDED! 1965 - 1973 Classic Mustangs -General/Talk- 3
K New to me 1966 convertible 1965 - 1973 Classic Mustangs -General/Talk- 2
E mustang 1966 Oil in intake Classic Mustang Specific Tech 7
R My 1966 coupe 1965 - 1973 Classic Mustangs -General/Talk- 7
R 66 Front disc brake conversion, Did a search and couldn't find an answer 1965 - 1973 Classic Mustangs -General/Talk- 4
F 1966 mustang buck tag info 1965 - 1973 Classic Mustangs -General/Talk- 0
A 1966 Mustang Help 1965 - 1973 Classic Mustangs -General/Talk- 1
A Engine Trouble 1965 - 1973 Classic Mustangs -General/Talk- 4
M Engine 1966 backfire through carburetor Classic Mustang Specific Tech 4
Sweetmarie66 1966 I-6 head conversion Classic Mustang Specific Tech 2
WarHorse66 1966 straight 6 harmonic balancer removal help!! 1965 - 1973 Classic Mustangs -General/Talk- 3
Paxton.5oh 1966 - Replacement Side Mirrors Classic Mustang Specific Tech 0
S 1966 mustang 1965 - 1973 Classic Mustangs -General/Talk- 1
I 1966 289V8 timing/bent push rods? 1965 - 1973 Classic Mustangs -General/Talk- 5
H 1966 Mustang 289 flywheel info needed Classic Mustang Specific Tech 7
M 1966. 289 compresśion is dropping Classic Mustang Specific Tech 8
Similar threads