Search results

  1. pumm3l

    79-93 Prothane End Link Urethane Bushing Kit

    sold
  2. pumm3l

    FRPP King Cobra clutch & Ram TOB (86-01 GT / 93-98 Cobra w T-5 / T-45)

    sold
  3. pumm3l

    FRPP King Cobra clutch & Ram TOB (86-01 GT / 93-98 Cobra w T-5 / T-45)

    sold
  4. pumm3l

    2x drivers side valve covers 4.6 (windsor)

    drivers side valve cover 4.6 (windsor) both covers sold
  5. pumm3l

    Boost-a-pump noise

    I just finished installing a 40amp BAP and I noticed when I turn the dial all the way up that the unit will make a weird high pitch noise. Is this normal for the unit to do this when turned all the way up or do I have a defective BAP? Video reference...
  6. pumm3l

    KB boost-a-pump

    I need to get the 40 amp kb bap for my setup because I'm maxing out my pumps. I know someone that has one for sale but he's not sure if it's the 20 amp or 40 amp. Is there a way to distinguish the two? maybe a part number somewhere? he said there's a 15 and 17 on the back of the unit but that...
  7. pumm3l

    pump assembly tubing

    I bought a cobra tank a few months back from a salvage yard, I was planning on finally putting the new tank on this weekend but I thought I should check out the pumps and make sure the tank was clean before I put it on. As I was pulling out the assembly the tubing on the pumps startled to...
  8. pumm3l

    6 bolt crankshaft

    Can I use the 6 bolt GT crankshaft in a 99 GT windsor block? The original crank had 8 bolts and thought I saw somewhere that those crankshafts (the 6 bolt) only fit in the romeo blocks, is that true?
  9. pumm3l

    power steering going?

    I did some searching and it seems like when the power steering pump starts to die it starts to make all kinds of groaning noises. My pump is pretty quiet no more noisy than usual but this morning my steering started feeling strange if I leave the steering wheel centered(foward) and try to...
  10. pumm3l

    valve tap?

    last year I replaced my engine because of a spun bearing. I've been driving around with this 02 explorer engine for almost a year and took it to get dyno tuned with the nitrous last night, my old motor I was careless and didn't check the oil before getting on the car thats how I blew that engine...
  11. pumm3l

    Defective flywheel

    I bought a flywheel back last year when I did my swap, decided while I had everything apart I might as well change the clutch and flywheel. Funds were limited after having to buy a new engine and all the other misc. parts I needed so I tried cutting corners as best as I could. I found this...
  12. pumm3l

    55mph steering vibration

    I recently fixed a vibration in my car that I was getting at around 1400 rpms (bad flywheel) but now I have a new vibration, was probably there all along but I didn't know realize because of the other vibration. Anyway This vibration I get at around 55 mph which is where it's worst, it starts...
  13. pumm3l

    Philly SCT Tuners

    I'm about to get a SCT chip and a dyno tune and I looked up some dealers in my area and the 2 that came up were: JD's Performance Center L & M Engines Inc Anyone have any expierence with either of these 2 companies? I've bought some nitrous refills from L&M but I don't know their...
  14. pumm3l

    Vibration around 1400 rpms

    did a swap about nov of last year while I was at it I put in a new clutch & flywheel after everything was done I now have a slight vibration at 1400 RPMs only, did a little searching some are saying that the pressure plate and clutch could be out of balance as a set, anything else I can start...
  15. pumm3l

    Flywheel

    spun a bearing in my 99 GT so I bought an 02 alumuinum PI engine, and I need a 6 bolt flywheel so figured might as well change everything out since this clutch has about 60k miles on it and I have to go in there anyway. I decided to go with a king cobra clutch setup but I'm torn between 2...
  16. pumm3l

    Explorer motor

    Well spun a bearing in my 99 GT and decided to go for an explorer motor since the stang is my daily driver and I drive atleast 70 miles daily, I've been researching this a lot the past few days but I have a few questions unanswered maybe someone can help here's what I've compiled so far: I...
  17. pumm3l

    Engine Knock

    Well yesterday I installed a shift light and I went out to test it obviosly I had to get on the car a little because I set my shift light at 6,000 rpms. Well anyway after I was done, between shifts I started hearing some engine knock which progressively got louder as I drove home luckily I was...
  18. pumm3l

    fuel pump install

    I bought a svt focus pump and today I went to install it. I dropped the tank and removed the metal plate that covers the pump assembly after that I discoverd the entire assembly is cocked forward like its on an angle with the top slightly facing the engine, I can't remove the damn assembly...
  19. pumm3l

    advertistments cover menus

    Whenever I come to this site every time I try to click a menu the advertisement at the top of the forums covers up the menu, for instance I can't select anything in the search menu because it goes behind the advertisement.
  20. pumm3l

    Fuel pressure...again??

    Well last week I thought I was having a nitrous related problem with my fuel pressure dipping down under WOT. Well today it happened again without using the nitrous. So far I've noticed this will only happen when I'm low on gas (1/4 or lower). My car idles at about 29-30psi and at WOT jumps to...
Top Bottom
Back
Forums
Menu