Search results

  1. 8

    So I bought a B303 cam............

    Its the typical is this cam ok for my setup thread!:rlaugh: but seriously, a lot of people are looking for the biggest cam yadayada yada... I just dont want to over cam my motor. I just bought a set of gt40p heads and sent them off the Russ Folpe, previously worked at Ford perf. solutions in...
  2. 8

    anybody buy parts from a user name of keri hope on here?

    Well i was going to send him some money for the edelbrock heads and tfs cam he is selling for cheap.But it was just weird, he wont accept paypal.......just cash or moneygram and hes in canada to boot. He mispelled his name on the email and the address' he gave me are clothing shops or it was a...
  3. 8

    Im havin some nitrous isuess.....lil help please.

    I just installed a 125hp dry shot on my stock H/C and explorer intake 89 GT. I have all the bolt ons plus 1.7 roller rockers. the car was running good all night and then after the 4th pass i popped my hood and saw my timing spout clip was sitting on my radiator!:nonono: I forgot to put it back...
  4. 8

    1987 5.0 coupe with t-tops!!!!

    Well i just bought an original 1987 ford mustang 5.0 coupe with t-tops from an old lady in a wheelchair that was in her back yard for wellll......CHEAP!! Its Bone stock with original everything, but is an Automatic. Interior is shot, body doesnt have a dent or crack in it,paints gone, Needs a...
  5. 8

    head gaskets to raise compression?

    Im going with a roush 200cc head with tfs stage 1 cam with 1.7's on a stock bottom end. I know the combustion chamber on the roush 200's are 64cc. that will lower my compression, which isnt good to me. i want to get as much compression as i can by using a thinner head gasket but dont want to...
  6. 8

    I bought my H/C/I combo, now.......pushrods?

    i went ahead and bought a pair of roush 200 heads, TFS stage 1 cam, 1.7's, TF track heat intake, 70mm throttlebody and 76mm mass air. The springs are manley springs on the heads so they are good, lifters are good(tfs), and i am lost on pushrods.....stock pushrods work? And also would 24lb...
  7. 8

    GT40 heads,Trick flow intake with TFS stg 1 cam?

    I am shooting for as fast as i can go with virtually not much money spent, like most other broke people! 89 GT 5 speed 210k miles These are the times ive ran and the mods at the time, all @ 11 degrees of timing stock suspension. 1/8th mile of course 9.21 @ 77mph with 2.0 60ft on street tires...
  8. 8

    Can i hook up a shift lite to stock tach?

    i have a monster sport comp tach with a shift lite, i really am not big on gauge thing. I like the stock look, but a shift lite would be very helpful. Can i hook up my autometer shift lite only to my stock tach? any help would be greatly appreciated. I cant find any answers any where else! thanks
  9. 8

    This sound like a good top end combo?

    Well I have a chance to get these parts for $1300. New Trick Flow street Intake Slightly used Roush 200 heads complete with FMS 1.7 RR's (Heads have 4 hours run time) New TFS stage 1 cam and lifter New 75mm throttle body New 76mm mass air with tube Used 24lb injectors I already have MAC...
  10. 8

    Bad vibration at 70mph

    It vibrates on the floor when i get to 65-70mph and it vibrates the whole car in a rotating sound. Its not constant loud vibration in one sequence, it gets real bad every second and quiets up a little bit then it gets bad and so forth. I will put it neutral and it gets worse. Then if i put it in...
  11. 8

    miss at low rpm

    Well i bought a 89 gt and threw on longtubes, o/r h-pipe, 65mm throttle body new plugs, wires, distributor cap and rotor. It has a miss at low rpm and i cant figure out why.It had it before i put all that on. Could it be head related? Valvetrain? Please any help would be appreciated. thanks
Top Bottom
Back
Forums
Menu