Search results

  1. LethalInjection

    PCV Hoses

    Does anyone know the purpose of the pcv having 2 connections on the upper intake to draw vacuum? I have the bottom one on the plenum capped off and am pulling vacuum through pcv via the one on the rear. Are there any benefits to the 2 hoses tee'd together factory approach?
  2. LethalInjection

    Video of my blue 95 GT

    Well, I finally got around to putting up a video of my car. The volume is kind of low because I had to take it with my iphone. You may have to turn it up to hear it. I hope you enjoy. YouTube - My 1995 Mustang GT at idle.
  3. LethalInjection

    Force o\l at idle?

    Can anyone tell me how to force open loop just at idle?
  4. LethalInjection

    Motor Mounts?

    Hey, does anyone know where to get solid motor mounts for the 94-95's? I can only find them for Foxes, and I'm not sure if it's the same mount. Does anyone know if a Fox one will work?
  5. LethalInjection

    Pacesetter longtubes and GT40P's?

    Hey, I was just wondering if anyone had any experience with the Pacesetter longtubes for 94-95's and whether they work well with GT40P's? I'm more interested if they will physically fit with the help of 90* plug wires. I will take the headers loose to change plugs if necessary. I already have...
  6. LethalInjection

    What tuning hardware for BE tune?

    Ok, I downloaded the Binary Editor software and built a base tune for my car in it. For now, I'm just looking to write this tune to my car, and don't care so much about the data loggin side of it, due to i'm unemployed at the moment and will get all that stuff later when I have more money. I...
  7. LethalInjection

    BBK Equal Lengths and GT40P's

    Ok, I've had my car since highschool and at some point I thought it was a good idea to get a set of BBK equal length headers. I now know I shoulda just went ahead and got full lengths but was young and planning ahead wasn't my specialty. lol Now, I've had a set of GT40P heads sittin in the...
  8. LethalInjection

    Initial startup problem.

    Ok, this one has me stumped. When I first start my car I can drive it for about a minute or so then it starts missing and running generally crappy. If you put it on the mat, it will go away, but as soon as you go down to part throttle or light throttle it's back. It will run this way and be...
  9. LethalInjection

    Where to buy new AC vents. Please Help.

    My AC vents in my 95GT have the directors all murfed up and I have been lookin all over the place to find some new ones. Is there a website anywhere that yall know of that sells these?? This is driving me nuts. LOL
  10. LethalInjection

    Opinions on possible setup..

    Well the ole stang's getting some miles on her now and I guess I've put off redoing it long enough. It would've probably already been done if I hadn't bought a jacked up 2000 Superduty and then gas prices went up. I have reconsidered my previous carbed combo in favor of the higher gas mileage...
  11. LethalInjection

    Flat top piston ?'s....

    As far as piston design goes, what affects the compression ratio of flat top pistons.. I know valve relief volume is a factor, but what is the difference in say... The 8.5:1 and 10:1 trickflow pistons.. I noticed that they have the low comp pistons listed with a larger compression height.. I...
  12. LethalInjection

    Does anyone know this?

    What will happen if you put an msd distributor with mechanical advance and hook it up to a 6AL box in a fuel injected car? Will this work right? I SHOULD know this.. I'm just not sure what effect it would have on the other functions controlled by the computer.. Fuel is metered by readings from...
  13. LethalInjection

    Mac FLowpath muffler sound.....

    Can anyone tell me if there is any difference in sound between the 13"L X 9"W X 3.75"th and the 18"L X 12"W X 4.75"th Mac FLowpath mufflers... Both of these offer a 3" diameter inlet/outlet, and I am looking for the best sounding ones... Since I will be upgrading to 3" mufflers for my future...
  14. LethalInjection

    RPM 2 Hood clearance?

    Hey, does anyone know if the Performer RPM 2 will fit under a 96-98 cobra hood? I think I have just about decided to go ahead and get one of these, but as of right now don't want to put on the 5.5" extended cowl that I have.. I thought that the cobra hoods have a little bit more clearance for...
  15. LethalInjection

    BBK intake manifold?

    Ok, I haven't really had that much time to mess with my car here lately, but I got the Bother's Performance catalog a month or so ago, and I noticed that BBK is now making an intake manifold... For the most part these guys seem to make some good stuff, and and I kinda like the idea of the...
Top Bottom
Back
Forums
Menu