Search results

  1. str8stang036

    SBF Edelbrock Victor Jr Heads w/ upgraded springs

    I have these Edelbrock Victor Jr heads 60cc with upgraded springs for hydraulic roller cams.They have less than 5 miles on them just mostly idle time. I am no longer pursuing my project. Springs have higher seat pressure. Asking $1300 Shipped
  2. str8stang036

    Ford Racing Traction-Lok 31-spline 8.8

    I have a Ford Racing Traction-Lok 31-spline 8.8 that I no longer need. It has less than 5 miles on it. Ring gear not included. Asking $170 shipped.
  3. str8stang036

    Anyone have stock springs to give away?

    Hello everyone, I am in need of some help. I am going to be selling my 95 Mustang as a roller because of money issues. Replacing everything back to stock but I am missing front and rear springs. Anyone have their stock springs to give away? I prefer it be in the south florida area, so I can...
  4. str8stang036

    Repainting interior tan, which paint?

    I am repainting the tan interior parts, I just dont know which paint matches it correctly. Which one did you guys use?
  5. str8stang036

    What was this electrical connector to?

    Hello everyone, I am in the process of removing all of my wiring from a donor car and found a extension from the main ECU harness that was cut. I don't know what its for, can anyone tell me?
  6. str8stang036

    Do I still need my ccrm?

    I have my Aeromotive fuel pump hooked up to a manual switch as well as my fans. I have no A/C. I know that the ccrm controlled these things, however I think I have already bypassed it with my current setup. Can I remove it?
  7. str8stang036

    Can I use c-clip eliminators with c- clip axles?

    I use c-clip eliminators with c- clip axles? I will be installing c-clip elims in the future and right now I have Strange 31 spline c-clip axles
  8. str8stang036

    MSD distributor timming

    I think I may have installed the distributor wrong. I have followed the tips from previous post, however I want to make sure I get it right this time. Its an MSD distributor for 351w (forgot part #), it doesn't have any reference lines at the base like the stock one does to know its been...
  9. str8stang036

    2001 Clutch disc size

    I am going to swap out the clutch on my 2001 mustang, however I am unsure of the size 10.5 or 11"
  10. str8stang036

    Need help welding bungs on valve covers

    I need a set of -12an bungs welded onto my Ford Racing Tall covers. I am in Miami, Fl and unfortunately I don't have a tig to do it. I went to a local place today and the old man told me $30 for each cover. He must be crazy! Any help is appreciated
  11. str8stang036

    Rocker adjustment

    I remember reading somewhere that new rockers need to be tightened like 1/4 or 1/2 turn after the engines been running for some miles. I need to do this, as I haven't done it before. What specifically is the amount of tightening needed? They are Crane 1.7, no noise from them at all.
  12. str8stang036

    Have an oil leak around oil filter

    Hello everyone! I have noticed that my '01 stang has been leaking oil for some time now near the oil filter. Its not the oil filter because I had replaced it and cleaned all the oil residue from previous leaking. I noticed that where the oil filter is, behind that there is a bracket or block...
  13. str8stang036

    Oil behind intake

    I have been having a throttle blip/buck from idle and stopped position. I haven't been able to tune it out yet, but today I discovered oil puddles on the block behind the intake. I assume this is a vacuum leak, am I correct? Jose
  14. str8stang036

    Some trouble with idle and tip-in

    I posted this on stangtuning.com also. Stangnet has helped me a lot so I thought I would also try my issue with you. I am using the Anderson PMS for tuning, this is my issue: I got the car started back up after changing my turbo placement. I am having the same issues I had the first time I...
  15. str8stang036

    Sounds like a cylinder isn't firing

    Finally got the car started and it sound like one of the cylinders on the driver side isn't firing. I can hear it in the exhaust and feel it when I put my hand against the exhaust. I changed all the plugs, since it had been a long time. The motor is new and has less than 10 miles on it...
  16. str8stang036

    Swapped out cracked intake now A/C doesn't work

    I just finished swapping out my stock cracked intake for another stock one and most things seem ok. Weird thing is now when I start the car the fan is constantly running on high and the A/C doesn't work, only fan setting. My coolant temp sensor isn't working, could that cause the previous...
  17. str8stang036

    Cranks but doesn't fire

    I am starting the stang up after months of reconstruction. The car cranks however doesn't even make an effort to fire. I did remove the distributor to install an new intake. So possibly it may be off. I also checked for voltage at the ignition coil and there is no voltage. Not sure why. I l...
  18. str8stang036

    Coolant leak from intake, need to replace

    Hello everyone, I usually don't post here, but it seems I have a problem. I have a 2001 GT and the crappy plastic intake is leaking coolant big time. I have to refill the fluid every day or two. My question is what intake do I replace it with a PI or non-PI? Its stock and I have no plans for...
  19. str8stang036

    Help me make my car doors out of fiberglass

    I have been thinking about doing this for a very long time. My car is drag only and I am trying to get as much weight off the car as possible. I have been to many NMRA events where cars have fiberglass or carbon fiber doors. This is what I want to do also. I need some help to figure out where...
  20. str8stang036

    Why won't my battery charge?

    Ever since I was able to start my car, the battery has never kept a charge. I have to constantly be charging it, luckily its a drag only car. But I am only able to get a few cranks out of it before its unable to work anymore. The alternator has been checked out and is ok, somehow it doesn't...
Top Bottom
Back
Forums
Menu