Search results

  1. B

    Polyurethane Motor mounts

    The poly mounts dont flex as much as the stock ones do so your motor doesnt waste power by moving itself instead it puts that power into the drivetrain.
  2. B

    new extreme compcams

    Whch grind?
  3. B

    2nd gear grind (t45)

    One thing I did try on mine was to drain the synthetic I was using and refilled it with type-F. Type-F isnt as slick as dextron or synthetics and it seemed to help the friction material grab the cones a little bit better. It eliminated the cold grind for me.
  4. B

    Which Man Tran Fluid to use?

    What year is your car? In my T-45 switching from synthetic to type F cured most of my grinding problem, well up until I broke a fork being a dumbass. Bear with me I cant get the words right. Type F isnt as slick as dextron or a synthetic and it seems to help the friction material in the...
  5. B

    1996 Ford Mustang Hydraboost

    I agree 100%
  6. B

    1996 Ford Mustang Hydraboost

    Dont come to a forum and be a dick. Some people around here are trying to help out as much as we can and people like you dont help. Sorry I missed your thread. If you want questions asked immediately buy a manual.
  7. B

    Can I use the MAF housing from an 02 GT with my MAF sensor from an '00?

    The only problem you could run into is if there is a size difference in the sampling tubes. Go to www.modulardepot.com and ask randy stinchomb in the ford parts forum.
  8. B

    new extreme compcams

    Comps are good. I personally have heard too many good things about VT to pass them up though. I will be going with VT stage 1's in a month or so.
  9. B

    2nd gear grind (t45)

    They are cast aluminum and dont bend they break, which is why my tranny is in pieces on my bench. www.hanlonmotorsports.com has 3 different rebuild kits from the basic syncro overhaul to the full on bearings and everything kit if anyone needs to know where to get the parts. There not that...
  10. B

    2nd gear grind (t45)

    Actually the blocking rings are worn out and the grinding you hear is the teeth on the syncronizer.
  11. B

    rear output seal

    What else do you need to know? Its not that hard.
  12. B

    4.10's too much for my goals

    Top right next forum tools you will find the search button.
  13. B

    4.10 GEARS

    I stand corrected. The race only gears are "harder" and are designed for closer tolerances for drag racing only. Since they are harder and I think the gear pitch is different they will make more noise than a street gear. Dammit I always get hard and soft thing screwed up oddly enough my old...
  14. B

    GEARS QUESTIONS????

    Ok vax sorry but I cannot help it. Why must you ask the same questions over and over and over and over again? Every time I see you post you re-ask the same questions multiple times. It would help to subscribe to your own threads so you dont get lost. Christ this was posted and answered...
  15. B

    New member :)........ (with some questions)

    Oh sweet jesus this is too much :rlaugh: :rlaugh: :rlaugh: :rlaugh: :rlaugh: :rlaugh: :rlaugh: :rlaugh:
  16. B

    Which Dyno?

    I am not that familiar with load bearing dyno's so to be honest I am not sure. I would think that as long as the timing and A/F ratio are correct it should be fine. Post your graphs if you can.
  17. B

    Which Dyno?

    Glad I could help. :banana:
  18. B

    rear output seal

    A hammer, chisel and about 20 minutes of your time if you can get the driveshaft bolts out. Take the driveshaft out obviousely and then either take a screwdriver or prybar and hook under the inside lip and pry it out or take the chisel and chisel up the outside lip and then pry it out. Clean...
  19. B

    newB confusion. Rouche/bullit/cobra/gt

    The cobra mustang is produced from a ford factory by the Special Vehicle Team and from 96 to 04 is powered by the 4.6L DOHC motor. The bullitt is a special edition GT and like our GT's is powered by the 4.6L SOHC motor and is also made in a ford factory. A Roush or Saleen is a seperate...
  20. B

    Which Dyno?

    Negative. The difference between those dynos is the dynojet is an inertia dyno and the other one is a load bearing dyno. The dyno dynamics is a load bearing like the mustang dyno. What that means is there is mechanical resistance applied to the wheels of your car to simulate what the car is...
Top Bottom
Back
Forums
Menu