Search results

  1. pro50

    mmats pro audio

    Mmats makes excellent products. I had a D200HC back in the day. That amp was badddd ass.
  2. pro50

    Do they make a plug in chip?

    Moates makes some pretty cool stuff. Yes they make a chip for foxes. Im looking into them actually. Ive been doing some honda dyno tuning at my shop and we use moates products. They have some decent tuning programs for EEC also. Im getting ready to do some experimenting with their fox tuning...
  3. pro50

    Pics Of Your Fox With Rims

    They Are center line Telstar terminators.
  4. pro50

    Pics Of Your Fox With Rims

    These are the wheels i chose. They were different. Ive never seen them on another fox.
  5. pro50

    New wheel fit issues

    I just put my 86 gt together. i added a qa1 k-member and did a 87-93 gt spindle conversion so i can go 5-lug easily. I want to run the centerline telstars and im havin a bit of trouble. I was going to run a 15x7 with 5 inch b/s. But left turn almost at lock the wheel just touches the control...
  6. pro50

    I'm tired of this project already....please help..........PLEASE?

    dude i pulled one from like a 91 ford tempo it worked just fine. most mass air cars in that year range used the same plug. try tempo,topaz,lincoln continental i know for sure has them. hope that helps.
  7. pro50

    aod to c4 swap speedo calibration

    i put an art carr built c4 into my 86' me not paying much attention, put the trans in without counting the speedo drive gear teeth on the output shaft. im curious if anyone might be able to give me a range of the tooth counts that c4's came with, i guess if i have to buy a couple gears to get it...
  8. pro50

    A4LD driveshaft vs. AOD driveshaft

    hey man, i will check it out for you. i have a 4-cyl drive shaft and the stock one from my 5.0, but they're a few miles away. ill have my dad check it out for me and let me know. im thinkin the a4ld shaft is slightly longer and i think its pretty small in diameter. ill check it out and try to...
  9. pro50

    fuel pump problems.

    well guys heres te outcome so far. ive done all the testing i think i can. i tested all the pins at the eec that are supposed to have either ground or 12v, they all seem to test fine. im thinking that my eec relay may be bad?? from what you guys said the eec relay provides power to one side pf...
  10. pro50

    VREF voltage too high

    hey, question for you. im having the same problem. im curious to see if your car will start or not.i cannot get my fuel pump to turn on or the injectors to fire and im seeing 12v at the vref wire. let me know what you find, maybe we can help each other solve our problems. thanks
  11. pro50

    fuel pump problems.

    hey thanks for the diagrams guys. these should all help. well im off to see if i can get her to work again. ill let you know what i find. thanks again. :hail2:
  12. pro50

    fuel pump problems.

    well all i know this sounds like every other post but it may go deeper. than those others. ive finally got everything buttoned up enough to start my new 331 up and get some run time on her. and ive got no fuel pump action. i have done the mass air conversion as my car is an 86. i can jump the...
  13. pro50

    timing chain verses timing gear

    ill be honest. i really wouldnt use a gear drive. i just experienced one going to hell in a 302 and the crank gear teeth were just about gone before i noticed the noise and timing jumping around severely. it was wasted bad. ive heard that they also take a lot of hp away because of friction. i...
  14. pro50

    Summit universal radiator

    radiator help hey man. summit radiators arent a bad deal. theyre not the most cosmetically sound things. but they work. i recently purchased a universal radiator for my 86 mustang. i was not happy with the welds on it. so i looked at a couple more. i looked at the direct fit mustang radiator...
  15. pro50

    afr 205 pushrod length on 302

    i got these afr 205 heads, getting ready to bolt on to my stroker. im not for sure if i will need to change pushrod length at all. i would like to have them before final assembly so i can check to make sure valves have enough clearance to the piston. does anyone know what length pushrods i...
View older results
Top Bottom
Back
Forums
Menu