Search results

  1. LarsD

    03 Cobra Dies At Random

    I checked the grounds on the core support, the plugs by the battery, and the one over by the ecu, any other that I might have missed?
  2. LarsD

    03 Cobra Dies At Random

    I've check, cleaned, and retightened the grounds (core support grounds, the ECU ground, and that ground connector hidden next to the battery), replaced the cheap Walmart battery with a Yellow Top Optima, and verified my alt is charging 14.3-14.4 volts at idle and running down the road with my...
  3. LarsD

    03 Cobra Dies At Random

    Been chasing this problem for a couple of months now and running out of ideas. The first time I had been driving for a bit (15 minutes or so) and was headed back home, in third gear, A/C on, and rolled into the throttle (60% or so at about 60mph). The car was making boost (10ish psi) and then...
  4. LarsD

    Progress Thread 1998 Gt Procharger Build--dyno And Track Numbers Inside

    Seems like it would have been less effort to put a TKO in it by now.
  5. LarsD

    Progress Thread 1998 Gt Procharger Build--dyno And Track Numbers Inside

    Well I was running shorties on a 347, so my case likely isn't typical. lol
  6. LarsD

    Need Help!! 4.6l Mustang Gt

    I may be a little late here, but it sounds like a bottom end bearing problem like you said. That being the case the engine has to come out. At the very least the crank will have to go to a machine shop to get turned, swapping a known good engine will be the cheaper option I imagine. Since your...
  7. LarsD

    2000 Gt Engine Swap- In Progress

    Having R&R'd several motors but not on a mod car I can only offer general advice. Use blue painter's tape and a marker to mark wire harness plugs so you remember where they go. Buy a box of sandwich bags to put bolts in, and write on the bags where you took them out. Even if you think you will...
  8. LarsD

    Progress Thread 1998 Gt Procharger Build--dyno And Track Numbers Inside

    They were definitely worth it on my Fox, idk about mod motors. I really want a set for my 03 and my 12. I'd have to be the one to install them though. o_O
  9. LarsD

    Progress Thread 1998 Gt Procharger Build--dyno And Track Numbers Inside

    Just read this whole thread. I can feel the heart break through the screen. You'll get it done though!
  10. LarsD

    2002 Mustang Racing

    This, battle boxes probably aren't a bad idea either.
  11. LarsD

    What Lug Nuts Are You Supposed To Run With 2000 Cobra R's?

    Forgot I made this thread. I called them and they told me I needed splined lugs.
  12. LarsD

    Buying A Terminator

    118K isn't really a big deal. There is a guy on SVT with over 300K on his and it is still running well.
  13. LarsD

    What Lug Nuts Are You Supposed To Run With 2000 Cobra R's?

    Like so: https://lmr.com/item/LRS-50189653/mustang-2000-cobra-r-wheel-18x95-9404-silver
  14. LarsD

    Buying A 1997 Procharged Cobra

    03/04 Cobra for sure.
  15. LarsD

    official 4.6 liter Mustang photo thread

    Finally got back into a New Edge (please ignore my terrible grass, been too hot to mow).
  16. LarsD

    Blast From The Past, Any Of The Original Crew Still On Here? 16yrs+?

    I'm still around, I pop in occasionally. Wasn't a mod crew member till late, been in Foxes mostly.
  17. LarsD

    Who Bought Theirs New And Still Own It?

    Bought my 12 new in Feb of 2012 with 2 miles on it. Just under 20K miles as of right now (old pic, but it still looks like this). I plan to change the suspension, because while I think it looks awesome like this, I hate the way it drives.
  18. LarsD

    What Do You Guys Think? 275/40/17's On The Front Of A 91lx?

    Nice. Making me want 03's even more now. Wish I could get them in satin new though. :-/
  19. LarsD

    What Do You Guys Think? 275/40/17's On The Front Of A 91lx?

    Cool, that's what I have. Should have asked, how low is your car? Mine is down about 1" or so on H&R track springs.
  20. LarsD

    What Do You Guys Think? 275/40/17's On The Front Of A 91lx?

    What spindles did you use for your conversion?
Top Bottom
Back
Forums
Menu