Search results

  1. 68rustang

    See the Motorcycle?

    As Zookeeper said that comment is just ignorant. That is like me saying I hate everyone that drives a car. Everytime I see them on the road while riding my bike they pull out in front of me, merge into me, or generally do not pay attention and I almost pay for it with my life. :nonono: I am not...
  2. 68rustang

    2005 bullet wheels on a 65

    Any of the parts stores should have lug nuts starting around $1/ea.
  3. 68rustang

    Starting car after sitting for year and half...

    just fire it up. A year is nothing if it was inside. If it was outside and exposed to drastic temperature changes condensation may have corroded things like rings to the cylinder walls.
  4. 68rustang

    2005 bullet wheels on a 65

    I would sell them and buy wheels that fit.
  5. 68rustang

    Specific explorer swap questions. (measurements)

    nevermind see above post ^
  6. 68rustang

    For those with 65-66 Stangs running modern 302s

    Are the rubber insulators in good shape?
  7. 68rustang

    For those with 65-66 Stangs running modern 302s

    All the small blocks use the same mounts.
  8. 68rustang

    remember the viper that drove off the cliff? full video

    Do Vipers not have ABS?
  9. 68rustang

    Reproduction Hood Hinges

    Well it turns out my hinges are just fine. I just needed an extra set of hands :) What we did: Removde the hood from the hinges. Loosened the three bolts that hold the hinges to the fender. Drop the hinge down as far as the slots would allow. Kept the rear slot as low as possible and...
  10. 68rustang

    Reproduction Hood Hinges

    How much were the refurbished hinges? I have already emailed the Ring Brothers about their hinges. They look nice but the price is ridiculous.
  11. 68rustang

    Reproduction Hood Hinges

    Does anybody have any experience with the repop hood hinges that are available? I am having trouble getting the hood aligned and am going to trysome of the tricks I have found in the forums. Before I spend the time messing with possibly worn out hinges I might just buy new ones, LMM has them for...
  12. 68rustang

    Milodon Oil pan question

    Good you have it figured out. I don't know if this is the pan you have. From summit: Are you talking about the hole that is barely visible on the right (back in the pic) side of the pan? I still don't think it is a dipstick hole. I have never seen a dipstick that threaded in, much less...
  13. 68rustang

    The SN65 project car

    They are on the main page, underneath the second "Special Note" box.
  14. 68rustang

    Help spec out a Reenmachine track day car...

    No, it's posted like there are a couple of different places to get the same thing. :shrug:
  15. 68rustang

    Making my EFI harness from an 89: What wires can I cut out?

    I removed the pins and wires as a whole for a couple of reasons. 1) I am anal like that 2) I could put them back if I removed something I later found out I needed.
  16. 68rustang

    Making my EFI harness from an 89: What wires can I cut out?

    I just finished doing the same thing except mine was a 95 harness so it was slightly different. Basically what you see on this diagram is all you need: Somethings that aren't shown need to have resistors wired in to keep from getting a check engine light all the time. Everything you need to...
  17. 68rustang

    Milodon Oil pan question

    You sure it is a dipstick hole? Usually through the side of the pan is a level sensor and the dipstick either goes through the block or the timing cover. Either way I do not know what size thread it is.
  18. 68rustang

    Help spec out a Reenmachine track day car...

    I have seen your fab skills, they are better than mine, and I didn't have any trouble making this little piece. Total cost was $10.00 and an evening's worth of time. These are available as well: EDIT: I didn't see that John Z had already linked to the M+ brace. M+ Maier LMM has the...
  19. 68rustang

    Idiots guide to body prep and defeating rust

    sandpaper, if it is light surface rust then 80 grit would probably be good for getting the rust out. If it is more pitted then maybe use a wire brush on a grinder.
  20. 68rustang

    Idiots guide to body prep and defeating rust

    sand it until the rust is gone, spray it with an etching primer, skim coat with bondo, sand it smooth, repaint whatever color you want. The rust does not need to be cut out unless it is pin-holed.
Top Bottom
Back
Forums
Menu