Search results

  1. S

    First time tunning with a pms

    I have my timing set at 10. I set my tps at .98. And set it up idle and wot. I am getting it to run well but I dont know if my numbers are dipping too low or too high in my tune. It has a very rich start up. It will flood when fully warmed up when you try to start it. I have gotten it pretty...
  2. S

    First time tunning with a pms

    I just hooked up my anderson motorsports pms unit in my car. I have a pretty good idea on whats going on. I filled out my vehicle spec sheet and sent it to them and what I got back isnt helping me out at all. It was pretty much empty. I anchor points set it up and so far when it drives I am not...
  3. S

    TPS problem

    I figured it out, I was being a dumbass.
  4. S

    TPS problem

    I am sorry about the wrong info up top. I cant get the tps under .12, It is fully adjustable So Why is this happening. That is as far down s I can get it, there is nothing in the way or binding causing it not to go back down below .1 volts.
  5. S

    TPS problem

    So I just insatlled my anderson pms unit and I am tunning everything to spec required in order to start tunning futher with the pms. I just noticed that my tps is wasy of. It reads under .4 and it wont go higher than that, it will drop to 0 but that is it. My car has a profesional products tb...
  6. S

    5 lug conversion question

    I am writing down all the parts I need and where to get them for my conversion but here is my question. I used to work at a parts store before I got back into the shop and I remember using a mic to measure both fox body and sn95 ball joints at their witdh they seemed to be the same width...
  7. S

    t-5 swap

    If you are looking at the firewall from the front of your car the hole you need to use is to the left of the old speedometer hole.
  8. S

    Just ordered a pms

    Hell yeah! My pms just arrived today. I already filled out my start up sheet. Now I am just waiting for my base tune to get faxed back. I read the whole manual. Seems pretty straight forward I must say. I understood everything in the thing the first read.
  9. S

    Looking for a used enkie wheel

    I tried. I just thought I would try. Cant find any on ebay either. I figured the best way to find one would be through someone who messed up a couple and maybe have a few good wheels out of the set they would part with.
  10. S

    Looking for a used enkie wheel

    I cant find them anywhere and I know that the wheels are discontinued but I have them on my cobra and I am looking for a used 18x9 enkie v1 series ex wheel for the front. I had a little accident. REALLY need to find one or two of these wheels. I bent one badly.any help finding this would be...
  11. S

    Stroker Kit Choice - Dished or Flat Top..

    I ordered that top end kit for my 347 build up. I used flat fly cut pistons for mu build because I am not using a turbo. I might use a blower later but not allot of boost. Alot would advice against that but I have seen lots of higher compession engine blown that makes tons of power and they dont...
  12. S

    Just ordered a pms

    I am not having trouble driving it. Start up mode needs to be tuned. Last week I dropped the fuel pressure a little and advanced the timing a little and it runs even better. Not that it didnt before just tunning it better is all. As far as my check engine lights. they dont stay on. If I dont...
  13. S

    Just ordered a pms

    I built a 347 with a butt load of other goodies. I converted the car to mass air before putting the motot in it. The car once warm runs pretty good. but start up issues timing issues and the rest up at 6000ft where I live I am having trouble tunning it. I am running everything on a stock 93...
  14. S

    Just ordered a pms

    I just ordered my new pms from anderson motorsports. I am pumped about this. I can finnally get my 347 to run right. any first time user advice would be awesome.
  15. S

    Side exhuast for fox body?

    That sucks. I dont have the skills to build them myself.
  16. S

    Side exhuast for fox body?

    I have a couple of muscle mustangs and fast fords that has a couple of fox bodys with side exit exhuast with rocker panels. How can I find these. I am replacing the hood font bumper adding a cobra rear bumper a saleen wing and I want those rockers. Anyone have any ideas? I would love to get...
  17. S

    High Altitude timing?

    I think I am going to purchase the stage 4 anderson pms unit. Its seems to have all the options for tunning that I need. And it seems easy enough.
  18. S

    High Altitude timing?

    347 twisted wedge r heads 1.6 rockers a pretty hot cam twisted wedge intake 70mm tb with egr 30 pound injectors 72 mass air pulleys electric fan no smog tremec axles 3.73 long tubes,x pipe, flowmasters all msd including the distributor etc..... 5 months worth of building STOCK ECM. there are...
  19. S

    High Altitude timing?

    I want to get an engine management system for this car. I need to program start up mode and change alot of stuff in regular mode to get this car to run right. What is the best bang for your buck and easy to use Kit? I will order one as soon as I narrow down a good unit.
  20. S

    High Altitude timing?

    Ok So lately the car runs good. The 347. But when I turn it off and want to start it again while it is warm I have to hold the gas down for it to fire up. When it starts its idles high and shoots black smoke when it first starts. Its like it floods while trying to start it up. it idles high for...
Top Bottom
Back
Forums
Menu