Search results

  1. Dave0803

    Checking For A Miss

    It's a stick. This morning when I drove it it seemed to be stumbling on acceleration a little. Never had a problem with it all last week. It sat this weekend and didn't get driven till this morning.
  2. Dave0803

    Checking For A Miss

    Mine doesn't seems to do it. It might not be a miss I'm feeling though, what im feeling is a vibration that I can feel in the whole car at about 1000-1500 RPM's. I've replaced coils & plugs, fuel filter, motor & trany mount. Other than that it seems to run fine. It's driving me nuts.
  3. Dave0803

    Checking For A Miss

    I have the predator tuner that will data log but I don't see anyway to look at the cylinders. What tuners will allow that? --- I am here: http://tapatalk.com/map.php?41ioin
  4. Dave0803

    Checking For A Miss

    Thanks man. I don't have any codes. The car just seems rough up to about 15000 RPM and then it clears up. I've replaced motor mounts, plugs, fuel filter, ect. and nothing has fixed it. I was down to the COP's but wasn't sure of a good way to check them. --- I am here...
  5. Dave0803

    Checking For A Miss

    I am almost certain I have a miss. It seems to be at low rpm's (below 2000). What is the best way to find out which cylinder has the miss? It's a 2000 GT. --- I am here: http://tapatalk.com/map.php?mkuwm2
  6. Dave0803

    Gauge Needles

    Anyone know where I could buy some custom needles for the stock gauge cluster? I looked at Black Cat Customs but the closest think the had was for an F150. Would F150 needles work?
  7. Dave0803

    Warning chime

    I had to take it out when I changed the dash and I don't remember it doing this before that. I'll try just removing the ignition switch and reinstalling it and see if that helps.
  8. Dave0803

    Warning chime

    Ok, so if that's the same as mine I guess my ignition switch is worn out.
  9. Dave0803

    Warning chime

    Is there more than one way to put it in? What do you need to do to make sure it's just right?
  10. Dave0803

    Warning chime

    I've been having a problem with my warning chime in the car going off when it shouldn't. With the car running and the headlights on...of you open the door the chime goes off like you left the lights on and parked the car. Sometimes it will also go off when the car is parked, headlights are off...
  11. Dave0803

    Metal shim under motor mounts?

    Yeah, your right. It is the heat shields. I found that out a little while ago. I just don't really see what those little sheilds would block.
  12. Dave0803

    Metal shim under motor mounts?

    Does anyone know what the metal shim under each motor mount is there for? Is there any reason to replace it when changing out the mounts?
  13. Dave0803

    ABS after lower spring install

    Are they that fragile? Could they be broken without looking bad from the outside? Is there a way to test them?
  14. Dave0803

    ABS after lower spring install

    Ever since it came back on it has stayed on steady. All the wires looked fine when I checked them before. I have no idea what I could have done.
  15. Dave0803

    ABS after lower spring install

    The other day I installed a set of lower springs on my 2000 GT. After everything was put back together I had the ABS light on before I even got out of the driveway. I took everything apart and found one the had a bunch of crap stuck to it and cleaned it off. This morning I took it to work. It...
  16. Dave0803

    Motor mount alignment

    The trams mount was replaced at the same time but again, not with the Ford part. What I've noticed though is i don't feels the whole car vibrate as much I feel it in the steering wheel. And this is in neutral so it's not the tires or suspension.
  17. Dave0803

    Motor mount alignment

    Well I looked at the mounts again and they seem to e right where they should be. They don't allow the engine to move much though so I guess they are just a little stiffer than the stock mounts. I'll have to get some new ones from ford. Thanks for the help.
  18. Dave0803

    Motor mount alignment

    I see the bump your talking about. Guess I need to make sure that bump is in the hole. Thank you. Has anyone used motor mounts from a local parts store? Anyone have any vibration with after market stock replacement mounts?
  19. Dave0803

    Motor mount alignment

    I don't really know him. I don't usually take my cars anywhere. I'm not sure what he is talking about either. Was hoping maybe someone else would.
  20. Dave0803

    Motor mount alignment

    Nobody? I was afraid I'd be the only one.
Top Bottom
Back
Forums
Menu