Search results

  1. smilts

    New Gt40p Heads Quick Questions

    Are these the gaskets? http://www.cjponyparts.com/fel-pro-cylinder-head-gasket-performance-1011-1-260-289-302-351w-1965-1995/p/HG10111/
  2. smilts

    New Gt40p Heads Quick Questions

    Thank you for the numbers Ill get those ordered. I'll also figure out how to turn on my location. I'm told with the P heads I need to replace the factory headers with after market?
  3. smilts

    New Gt40p Heads Quick Questions

    I hear that a lot just go down to the parts store lol. The parts store is over 100 miles away. But Ill order some felpro gaskets thank you.
  4. smilts

    New Gt40p Heads Quick Questions

    Its the one in the Picture I was told a true gt40 intake, but not sure after looking at it. Im using the throttle body off of my mustang with a edelbrock adapter elbow. I'm not sure that i'm getting full throttle honestly. I havent purchased the gaskets yet, just the heads. Also are upgraded...
  5. smilts

    New Gt40p Heads Quick Questions

    I know that either the 3bar or 4bar heads need upgraded springs not sure which or if I need to replace the ones in the new 4bar heads I purchased? Also what kind of head gaskets should I go for? Heres a link to the heads I bought...
  6. smilts

    GT40 install went wrong

    They have been fairly recently reset. However since it cleared up a lot in the middle of pulling codes I don't know that I trust what I pulled. So Ill fix the minor thermostat housing water leak and do exactly what you suggest and see what I have. Thank you for your advice.
  7. smilts

    coolant leaking problem, under thermostat housing

    possibly the intake isn't sealed well???
  8. smilts

    GT40 install went wrong

    So out of frustration re pulled codes. I have a bunch. however in the middle of pulling the codes the idle smoothed out and the car started to run better. not perfect but better. I put the original complete air system back on. I have the following codes. C113, 157,158,334,556 R116,314,311,334...
  9. smilts

    GT40 install went wrong

    Sorry I'll clear that up there were no codes showing problems. pulled the cods off the passender side fire wall where my OBDI code reader plugs in.
  10. smilts

    GT40 install went wrong

    No, thats a good question but yes I did pull the spout. As far as I can tell I have a small water leak around the thermostat housing but everything else looks good.
  11. smilts

    GT40 install went wrong

    So I pulled codes and got nothing at all. Same problem still exists. Ive went through double checked all my vac lines and plugs sensors. My question is. Is it possible i need larger injectors? Im running the stock 19pound. I figured with my setup that would be plenty. I have a stg 1 trick...
  12. smilts

    GT40 install went wrong

    Im going to reinstall the BBK tomorrow pull codes and see what I get thank you.
  13. smilts

    GT40 install went wrong

    Hmm I put the old unit back on and same problem.
  14. smilts

    GT40 install went wrong

    Thnx Kurt I threaded and plugged it. Now me and the bbk cold air are arguing. With the MAF plugged in it runs but no power. Unplugged it runs badass. I had to switch the MAF module off of my MAF on to the one on the BBK. I'm not sure what hte problem is though.
  15. smilts

    GT40 install went wrong

    The lower intake bolts were a bit loose. But I believe I found the problem. Im just not sure what to do about it. . the upper intake splits to eitherside instead of blocking the hole in the center??
  16. smilts

    GT40 install went wrong

    Thank you for the advice ill be going over eerything slowly looking for a leak as soon as the snow goes away again. Good news is the balancer is brand new.
  17. smilts

    GT40 install went wrong

    I installed my gt40 intake and BBK cold air. the car after trying to set the timing for a loooong time barely runs. And it sounds as if it has a exhaust leak coming out of the lower intake?? Really messed with it for two days. Anyone have ideas? I could get a video of what its doing if...
  18. smilts

    GT40 intake install question

    Thank you I think that picture will get me what I need. it has 2 trees off the center of the plenum. I believe I can take the small tree off the old intakeand put it on hte elbow adapter for the EGR and FPR.
  19. smilts

    GT40 intake install question

    My OE intake had one line going in. and 2 lines connected coming out going to the PCV? Im not sure which vac ports to use for these lines? Also the adapter elbow doesnt have the small vac tree coming off it like the old intake. The fuel pressure regulator and EGR vac were connected there on...
  20. smilts

    GT40 intake install question

    Ive probably missed it somewhere. But I'm trying to figure out how to run the vac lines on my new intake. Seems theres way more vac ports on it than I have lines to go to it, not sure which is which. a picture would be great. Im using a PP adapter elbow with my stock throttlbody on it, if...
Top Bottom
Back
Forums
Menu