Search results

  1. 5

    no start after warm-up

    well rebuilt 302 see sig on mods. car starts great,good idle, runs normal with a small slight miss nothing major. timing at 11*. when the car warms up it will not start. i replaced the TFI and the 130amp regulator cuz the alt. gets hot while the key is on is that normal? i pulled codes they were...
  2. 5

    how 2? test if eec is fried or working?

    koeo: ect, tps, tad and tad codes??? half to check fire and fuel when i get home it was getting late.
  3. 5

    how 2? test if eec is fried or working?

    well i converted to mass air ran great up till i turned it off. now wont start. went to start up for the timing after i burped the system. any way to test the eec if still working? :shrug:
  4. 5

    noticable smoke from one tailpipe?

    ill take the one way conversation to the top...well changed tps still no signal there, O2s, plugs @ .50, timing at 10*, MAP. i guess ill try a mass air conversion
  5. 5

    noticable smoke from one tailpipe?

    ttt?
  6. 5

    noticable smoke from one tailpipe?

    ok i pulled the plugs drivers side are a dry black soot smells very rich. pass side black wet soot smells very rich.
  7. 5

    noticable smoke from one tailpipe?

    H pipe, im sayin im gettin no power at the green wire. havent pulled plugs yet KOEO were. 51,53,35 and 67
  8. 5

    noticable smoke from one tailpipe?

    smoke looks grey\white, but out mostly 1 pipe?
  9. 5

    noticable smoke from one tailpipe?

    just rebuilt a 89 302 with E cam, ported E7s explorer intake and Tb runs kinda rough but stays running.set timing to 14. i get smoke from the pass side tailpipe. smells rich any ideas? Also i cant get a reading on my TPS. i get low power from the orange wire but no power from the green wire.
  10. 5

    starter hook-up?

    my 86 starter has 1 wire hookup but the mini starter i got from a ranger has 2 wire hookup with the solinoid on the starter . can someone explain how to hook this up? where does the little wire go?
  11. 5

    missing valve seals???

    so do i put the rubber cups on both valves???
  12. 5

    missing valve seals???

    bought a rebuild kit and i think that there are some valve seals are missing i got 16 of these black rubber peices and only 8 blue seals with the rings around it. do the 8 blue seals go only on intake side and the black ones over the intake and exhaust stems?
  13. 5

    power steering hose?

    well how about teflon tape?
  14. 5

    power steering hose?

    what do you use to seal the hose? i see there is a white gasket but they tear up easy
  15. 5

    Way Too Rich!!!!

    what about MAP/BAP sensor i beleive the MAP vac. line needs to be open to open air while the BAP line runs to the manifold. my hose had a crack in it making the car run VERY rich. i put a new line on and ran great
  16. 5

    NEED HELP swaybar mounting location

    THANK YOU THANK YOU THANK YOU!!! you rock hopefully i get this project done before the dream cruise.
  17. 5

    NEED HELP swaybar mounting location

    guess i go ask on corral.
  18. 5

    NEED HELP swaybar mounting location

    hmmm anyone? please dont make me get on the knees.... wait i am :shrug:
  19. 5

    NEED HELP swaybar mounting location

    ttt
  20. 5

    NEED HELP swaybar mounting location

    ttt
Top Bottom
Back
Forums
Menu