Search results

  1. 2k2fourpointsix

    Charging A/C have a few ?'s

    I've recharged the a/c in a several other vehicles, but not a stang. It works great for the summer...But by the spring it has leaked out again. It is usually only a temporary fix. If I was you, buy the can with dye in it as well, it will help you or a shop track down the leak.
  2. 2k2fourpointsix

    Easiest and cheapest way to measure FUEL PRESSURE?

    Turn your key to the start position, press down and hold the odomerter button on the dash, then start the car. The digital readout on your dash should say "test". Press the odomerter button a few more times for some various digital readouts, one of those is fuel pressure. :nice:
  3. 2k2fourpointsix

    I wanna make my engine run on all 8 on demand

    But the most important question is.....WHY?!!!!! :shrug:
  4. 2k2fourpointsix

    Bad exhaust install....need help.

    The magnaflow clamps are junk, they are so cheap that they can only be tightened once. If you try to loosen them and re-tighten, they snap. I replaced all the clamps that came with my cat-back with some heavy duty ones from autozone. Bring it to a good exhaust shop and they will be able to...
  5. 2k2fourpointsix

    Mods needed to beat a G35

    No problems here losing to luxury sport sedans. Dead even in first, then I gain like 2 cars in second gear. He was flying solo I had a passenger as well.
  6. 2k2fourpointsix

    First time using dr's ?'s need answering

    I only have about 10 runs with mine, but I found that a 3-5 second burn works best. At the track I go to they don't prep for street nite so I only launch at about 3K by just dropping the clutch and they hook right up. Start at 18 lbs. and work your way down to see what works. 15-16 worked...
  7. 2k2fourpointsix

    Calling all 02 GT owners!

    Magnapacks, steeda pullies and t/a gears Tri-ax shifter
  8. 2k2fourpointsix

    Billet pedal cover install

    i just installed mine sunday, trust me the gas pedal is the easiest one. Two bolts, and use a screwdriver to pop off the throttle cable. use a hammer and a screwdriver to punch out the pin holding the old pedal on. Then just hammer the pin back in with the new pedal. use some wd-40 on the pin...
  9. 2k2fourpointsix

    Kenny Brown Side Vents Installed

    I agree with painting to match the car, but I like the function of them, and they are original.
  10. 2k2fourpointsix

    Bullit Pedal Install

    Ok its supposedly a 30 minute install, but in reality I spent close to 3 hours trying to get the brake and clutch pedals on. Probably the hardest vehicle mod I have ever done. One of the install articles I read said to push down on the pedal with your foot and twist back and forth to get it to...
  11. 2k2fourpointsix

    anyone heard of SuperTech oil?

    Its pretty much junk, I woulndt use it in a vehicle I plan on keeping long, or drive hard. I buy regular supertech for my beater cars.
  12. 2k2fourpointsix

    Alternator pulley

    If you managed to put get the crank pulley off on your own, you can take the alternator off too on your own. Real simple, Take a flat head screwdriver insert it inside the front side, not the top, of the alternator. Wedge it against the stongest part of the little fan blade inside there. This...
  13. 2k2fourpointsix

    Stock Fuel Pump

    Forget what the dealer says, install whatever pump you desire. The fuel pump has NOTHING to do with the emissions of the vehicle.
  14. 2k2fourpointsix

    Clunk/Thud Sound when Defrost or A/C is on.

    Its the a/c compressor cycling on and off. It is normal. They design almost all new cars like this now. By having the compressor cycle on and off when defrost is used it helps keep the compressor lubricated in the winter months when its not used. It will keep the a/c system from developing...
  15. 2k2fourpointsix

    99+ removing interior panel that covers the rear speakers

    Im trying to track down an annoying rattle that coming from the carpeted panel that holds the rear speaker grilles on my 2002. I didn't know if anyone has removed this piece and could give me advice on the easiest way to do it. There are a few push pins that hold part of it in, but I cant...
  16. 2k2fourpointsix

    tires to replace stock bfgs

    The stock tires are not BFGs they are goodyears but anyway nittos are ok, check out www.tirerack.com
  17. 2k2fourpointsix

    Rev limiter: Did I hurt the stang?

    So is it bad to be bouncing off the limiter when doing a burnout at the track in 1st, or doing a brake stand on the street?
  18. 2k2fourpointsix

    Will this shift knob fit a T-3650?

    I have seen the MRT knobs on here but I liked the look of the white Hurst. My only problem is I can't find a white Hurst knob with the 12mm threads, only black. Do you know where to get one, or one similar to the hurst (other than MRT)
  19. 2k2fourpointsix

    Will this shift knob fit a T-3650?

    http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=33703&item=2455175059 It says the threads are 3/8 -16, but will this fit a t-3650 threads? This is the shifter I want but I don't think it will fit my threads. Doe anyone know where to get one that will work. Any help?
  20. 2k2fourpointsix

    The curb ate my wheel last night, Need a new One!

    www.buyfordmotorsport.com Same thing happened to me last winter. I picked up two new ones from here, best prices I found on the net. Showed up in less than 2 days. I kept my scraped ones and mounted some BFG DR's on them for track use.
Top Bottom
Back
Forums
Menu