Search results

  1. 8

    Ignition questions for higher HP

    With out the charts and graph i cant tell you what happen. Can you duplicate this concern on the street? It would be nice if you could get those charts that the guy is refuring too. If you could get those then i could help you out alot more.
  2. 8

    traction problems

    ^^^ join the club of traction less life.
  3. 8

    e-85 fuel?

    your car wont run on it eaither. It requires a totaly diffrent fuel system and pcm stradegy. Thats why they make flex fuel vechiles such as the taurus and ranger. You need a diffrent tank injectors, ect.... it take a lot more of e85 to produce the same about of power of gasoline so the...
  4. 8

    Ignition questions for higher HP

    Well msd boxes are great and all with your setup i dont think it would be necessary. I personaly run a 6A box and love it. The 6AL is a upgraded box from that and works really well too. How did the guy know it was ignition related and not fuel related did he have a scope hooked up...
  5. 8

    Solid motor mounts

    you are not going to want solid for a street driven car. The vibration are going to piss you off so bad. Poly mounts will do just fine with little/no vibration increase.
  6. 8

    tranny problems

    If the clutch wasnt fully disengaging it would do it in all gears. Especially a grind into reverse. But since he is only have a grind into third i would look at 3rd gear blocker ring. Make sure its within spec and has good friction material on it. Also make sure the teeth are not all chewed...
  7. 8

    carrier pin won't go back in

    make sure your pinion gears are lined up with the hole. Sometimes turning the diff by the axle cause the pinions to walk a little and not line up with the carrier any more. Double check that. Other than that i havnt heard anything weird with the pin not being able to go back in.
  8. 8

    Dart Blocks

    Dart was made for the serious racer in mind. The reason why they dont pre make them for assembly is because all parts are not crated equal. When you order a set of pistons every single on will have a slight diffrence in bored diamater they allow you to get piston to wall exactly the same on...
  9. 8

    Vacuum Question

    Here are a couple tips for finding vacuum leaks for what its worth. First tip carb clean its your friend. Take a can of carb clean while your car is running and spray it in locations of suspected areas. If you hit a leak your cars idle will bump up. caution dont catch your car on fire :)...
  10. 8

    welding toqure boxes

    yeah stock street drive there fine but modded car with slick and UBER launches they dont fly.
  11. 8

    welding toqure boxes

    While your there i would say yeah weld them up. The ones on my mustang are welded. If you plan to have a high powered application it is really a good idea to do it. The stock tac welds tend to be weak.
  12. 8

    Why 93 Octane?

    octane is a rating on how volitaly (sp) gas is which means how fast it evaporates/burns. Your car will run the fastest with the lowest octane gas that doesnt make it ping. The benifits of running 93 or premium gas is that you can run more aggressive timing also more boost if you have a...
  13. 8

    How much can a T5 Handle

    Sure any tranny will last you if your easy on it. If you dont boost the crap out of it. Hard launches, gear slamping kill em. Nice granny shifts smooth throttle rolling will do you good. I dont think youll have a problem if you do a simply 8-10 psi setup.
  14. 8

    fuel cutting in third gear???

    Sounds like a fuel volume issue. Vacuum leak would cause the car to run lean and be an issue. If you can get ahold of a fuel pressure gauge monitor pressure ramping through the gears. If it drops your most likly looking at a fuel pump. (since you just replaced your filter). When you hit WOT...
  15. 8

    Coolant in my oil. WHY??

    what he said front cover. but if its that bad it looks to me like your going to have to start by removing your heads. Check the block surface, head surface, gasket, ect. You can also inspect the front cover at the same time. If you can get ahold of a block tester or have one. Test to see if...
  16. 8

    Hissing sound from air filter after motor is shut off??

    excatly what the last guy said. If you have a free flowing intake kit it will amplify the sound.
  17. 8

    People saying I will have problems when I assemble my combo?!

    i have been running 1.7 fms roller rockers made by crane for a long time now. They work GREAT!! No problems. not sure about the clearance issue youll have to do some research. Your not going to hurt the block with that amount of mods there are people on here running power adders with the...
  18. 8

    tps tec

    I dont know never seen it so I did a google search and found it. Hmmm... I dont know I kinda stay away from things like that. I would be kinda warry about it. If your factory tps has dead spots or doesnt reach 5.00v at WOT then replace it. Its designed to not have dead spots in the sweep. I...
  19. 8

    Small electrical fire...help!

    I would next do a very good visual of the harness. Make sure its not rubbing on anything it could ground out on. Try testing for countinuity while wigglying the harness. It could be a intermitant problem. If everything checks out fine put a new fuse in and retest. Remember a fuse...
  20. 8

    Selling notch for 14sec turbo coupe

    298 wheel ponies would be way faster than 14.2 did he just burn rubber half way down the track or are those flywheel #'s or estimates.
Top Bottom
Back
Forums
Menu