Search results

  1. Markus

    CFM flow rating question

    Hello guys, where is the primary bottle neck? Is it my 65mm ford racing throttle body or is it my (unported) gt40 tubular intake? :shrug: Any idea? thank´s Markus
  2. Markus

    SPAL electric fan controller

    Hello guys, i´m running the spal fan pwm for 1 year now. I´m very happy with it. Also i use the dual spal fan setup. The temperature sender is also from spal. This combo helped me over a lot of hot days.:hail2: Markus
  3. Markus

    electric fan with coolant sensor ???

    Yes, this are exact the same :nice: The sensor is spal temp sensor that come with my spal fan pwm unit but you can use any 3/8 bsp temp sensor. Markus
  4. Markus

    electric fan with coolant sensor ???

    Hello, i use a sensor adapter like this one. Markus
  5. Markus

    hydroboost conversion

    Hello guys, i have a hydro booster out of a 03 mustang lying around. I like to build it in my 67 mustang. :nice: But the 03 master cylinder flange is roughly vertical. My wilwood master cylinder have a horizontal flange. My question is now, can i flip the booster about 90 degree without to...
  6. Markus

    Such thing as a short oil filter?

    I´m not a friend of the fram filters. The metal is very thin and they tend to burst. Especially with cold engines and high oil pressure :notnice: Markus
  7. Markus

    Such thing as a short oil filter?

    I use the K&N #hp-2004 for 10 years now. Very good stuff :nice: HP-2004
  8. Markus

    march crank shaft pulley question

    Hello gals and guys, I need the dimensions and measurements of the march crank shaft pulley #2033. Diameter, deepness and the location of both serpentine grooves. On the march web side i found no information and the tech support don´t answer on my quests.:notnice: I know the pulley is a part...
  9. Markus

    Autometer Cluster -- 1967-68

    Hello, i do this work a few years ago. I took a plastic gauge support behind the autometer gauges. The new gauge bezel i trimmed with a soldering iron and remove the big aluminium rings around the autometer ultra lite gauges. I made a few pic´s. gauge cluster Markus
  10. Markus

    What Seats Will Fit in a '67-'68 Mustang

    Last summer i installed a set of procar seats in my 67 fastback.:D The quality is top notch and the installation was a simple job :nice: The seat is about one inch higher than my old buckets. But that is no problem for me. More pictures: procar installation Markus
  11. Markus

    new manual steering box or tcp manual r&p

    The front end is completely new. Roller upper and lower control arms, roller spring perches, adjustable strud rods, new pitman arm, new inner and outer tie rods (with tcp bump steer eliminators) :nice: The only old part is the steering box :( @65fbe2 i looked for the rrs r&p too. But i´m...
  12. Markus

    new manual steering box or tcp manual r&p

    Thank you guys for the comments. :hail2: I think i go with a new 16:1 steering box. The guys in the early days race with the worm gear boxes. So they can´t be so bad. The r&p stuff is also 2-3 times more expensive.:notnice: The bad turning radius is a fat CONTRA too. @yelorx7 thank you for...
  13. Markus

    new manual steering box or tcp manual r&p

    Hello guys, my old long shaft steering box is worn out and i have a lot of play in the steering wheel. Now is my question, should i buy a new flaming river steering box or should i go with a tcp manual rack and pinion conversion? For less play in the steering is the r&p the way to go, is...
  14. Markus

    14" Wheels & the CSRP disc brake kit?

    Hello, the kit has 11.25 inch rotors and kelsey hayes 4 piston caliper. The same dimensions like my ssbc kit. My 14 inch styled steel wheels fit without problems.:nice: Markus
  15. Markus

    Bear brake experiences

    Hello, do anyone have experience with the bear serious street front brakes with 11 inch rotors and pbr caliper? :shrug: thank you Markus
  16. Markus

    JMC hydraulic clutch and Power brakes.?

    Hello Jay, i don´t understand your question/info.:shrug: I don´t custom weld or modify the master cylinder. The kit come as followed....... Markus
  17. Markus

    JMC hydraulic clutch and Power brakes.?

    This is my jmc setup with a fox booster..... Markus
  18. Markus

    Optimal Front Tire size 67-68 mustang w/15x7 wheel

    Hello guys, i´m running 215/60 15 on 15 x 7 magnums front too and 225/60 15 on 15 x 8 magnums rear. I think they are not too small :nice:
  19. Markus

    professional photo shoot with my 67 fastback

    Yes, i like this combination (color,wheels) so much. The color is like the original color on this car from 67. clear water aqua metallic.:hail2: The photos are for my own usage. A few of them i place on my web side. And i make a big hard cover book. On my web side are a lot more of (not so...
  20. Markus

    professional photo shoot with my 67 fastback

    Hello guys, thank you for the flowers :hail2: I don´t know if the notchback is a original police car but it looks and runs awesome. The owner is the photographer. :nice: Here is a bigger picture of the fox mustang...
Top Bottom
Back
Forums
Menu