Search results

  1. bock

    Show me a pik of your Taurus elec. fan...

    I have a taurus fan here,but im not sure if it come from a 3.8 v-6 engine. It have 2 wires(1 speed?) and have 6 blades. Is this the good one?
  2. bock

    ALTERNATOR PULLEY

    i use the march pulleys kit.(3 pulleys) With all 3 in place,the alt was not charging at idle. I just put back the stock alt pulley in place...
  3. bock

    373 and burnout gear...

    When doing your burnout before drag racing,do you do it in first or second gear? This with 373...
  4. bock

    4cyl Suspention on 5.0

    i have 4 cyl springs in the front.Just install them today.With my setup, it drop the front of 1 inch.The front was siting to high because the alu heads and gt-40 intake,delete sway-bar...Now with thoose spring and my adjustable lower control arms... the car sit about 1 inches lower at all 4...
  5. bock

    question about resurfacing a flywheel.

    Can it be resurfaced more than once? my cltuch as been change once and the flywheel was resurfaced. Now i need a clutch,can i do the resurfacing job again on the same flywheel?
  6. bock

    Grinding tips of axles after trac-lock rebuilt.

    someone else ?
  7. bock

    Grinding tips of axles after trac-lock rebuilt.

    how much space do you have? i did grind them... i have .005 on each side... is this ok?
  8. bock

    Grinding tips of axles after trac-lock rebuilt.

    Ok! So i am rebuilding my trac-lock with a FMS kit.I used the same .35 shims and the 4 clutchs insted of 3 method for more grip. But now when i try to get the big pin back,its stop by the tips of the axles. I can see that i need a fiew tenths... Can i grind the tips of my axels a...
  9. bock

    A new stock throw out bearing and a centerforce clutch...

    Ok! cool! im wating for my centerforce.... i will order a Throw out at my ford dealer....
  10. bock

    A new stock throw out bearing and a centerforce clutch...

    Hey! Can i use a new stock throwout bearing from Ford and a centerforce dual friction clutch? (disc and pressure plate). thks!
  11. bock

    RPM CONVERTER HELP ON LM1

    I think so! cause you can plug a shift light in the 6aL,and its need a RPM signa...
  12. bock

    Help me tune my 12.XX stang.

    The big question about the chip: How do we choose it???:shrug:
  13. bock

    Do i need a chip?

    look at my sig,do i need a chip? Is there some hide power in this car? thks.
  14. bock

    Help me tune my 12.XX stang.

    Hi! I need a tool to help me tune my engine.I know that the LM-1 with RPM converter is popular. But,will i be able to tune my A/F ratio only with this tool,just buy adjusting the fuel pressure and timing? Or will i absolutly need something to tune my EEC?(tweecer,PMS...)
  15. bock

    Is the harmonic balancer supposed to be this difficult to remove?

    and how do you fix it back in place with the crank turning.
  16. bock

    Tuning with a Potentiometer,AFPR and a LM-1

    someone else?
  17. bock

    piston to valve clearance

    I run stock piston with TFS/tw and a f-303... 1.6 RR and i have over .100 of clearance on both valves.... You should always check it... i used the modling clay method.
  18. bock

    Tuning with a Potentiometer,AFPR and a LM-1

    Hey... Will i be able to tune my engine with just a LM-1 wideband equip with the RPM converter and an ajustable fuel pressure regulator? What is the MAf trick that use a potentiometer? I no that its to adjust the 0-5V signal from the MAf to the ECC,but how do you adjust it? thks.
  19. bock

    LM-1 wideband question.

    Do i need more than the basic LM-1 kit from Innovate to read and tune my A/F ratio? the kit----> http://www.innovatemotorsports.com/products/lm1.php
  20. bock

    Need Clutch Adj. Help I'm Going Crazy!

    Do you have the noise when pressing on the clutch pedal? If not,you need a throw out bearing...
Top Bottom
Back
Forums
Menu