Search results

  1. S

    Possible Bent Pushrod?

    alright so most likely it is fouled plugs ill change them up tomorrow and let you know how it goes.
  2. S

    Possible Bent Pushrod?

    You think after only 200 miles the plugs would be fouled? I was thinking maybe now it is a loose rocker because i never tightened them after i put the motor back together and let it run. Arent you suppose to tighten them again after like 20 minutes.
  3. S

    S/C guy needs help

    try puttin a breather on your valve cover instead of the oil cap.
  4. S

    ANY MUSTANG GUYS IN AZ...CRUISE SOON

    I use to live in az up in anthem. If you want some racing go down to scottsdale to the "illegals" as they call it. Theres some nasty racing that goes on down there.
  5. S

    Possible Bent Pushrod?

    Hey guys the other night i was out and i hit it real quick in second at about 3,000rpm and the pipe from the supercharger popped off. When i put it back on and went to start it back up there was a very violent shake at an idle. While driving as well it shakes severly. The car will idle run and...
  6. S

    Just Dyno'd Car

    .491/.509 212/222 107/117 @.050
  7. S

    Just Dyno'd Car

    im pretty sure its the 3.33 puley i know for a fact that its not smaller than that. Rick i would like to make a little more power but it is the stock block so i dont want to push it. Also My A/F ration is dead nuts with 12:1. Thats with no tuning. Just a little twisting of the distributor thats...
  8. S

    Just Dyno'd Car

    No no porting has been done to either the heads block or intake. Im trying to get the dyno sheet up but my scanners not working im going to my buddies house right now to scan it.
  9. S

    Just Dyno'd Car

    Here my set up Vortech supercharger 12-14lbs boost, BTM, edelbrock heads, Gt-40 intake, wolverine cam, 1.6 roller rockers, 80mm maf, 42lb injectors, FMU removed, 1 5/8 headers, H pipe, Mac Dumps, 255lph in tank fuel pump, 9mm plug wires, Firewall Adjuster, King Cobra Clutch, Drive Shaft Loop...
  10. S

    My Set up

    Hey guys just did a vortech s-trim, gt40 intake, edelbrock heads, 42lb injectors maf no fmu no chip no tuning a 255 intank and my a/f ratio is right on 12. I just made 473rwhp and 446rwtq. ill post the dyno sheet once my scanner works.
  11. S

    New Altenator Wont Charge

    yea i wired the one single wire in. Ill check it out and see if its loose. Also with the 130amp alt did you have to pull a pin?
  12. S

    New Altenator Wont Charge

    i didn't see anything when i was looking at it but ill take another look. Thanks.
  13. S

    New Altenator Wont Charge

    Hey guys i just installed a PA performance 130amp altenator. I wired it in and now it wont charge the battery and is pulling a battery light. I checked it at the battery and it was only pulling 11 volts. Any suggestion on what to do? or to look for?
  14. S

    BTM and Ignition?

    Hey guys i have some generic ignition with a rev limiter on it and i also have a btm for my supercharger. Can i splice into the ignition wires and wire in the btm?
  15. S

    Diff Fluid

    I used valvoline high performance gear oil. Think it has the additive in it already? i used an 80w-90 if that matters.
  16. S

    Diff Fluid

    what is friction modifier? I have limited slip additive if thats the same?
  17. S

    Supercharger Belt Broke

    I went to napa they only had the 54.25 long and it wont fit over the pulleys they say it needs a 54.50 i guess ill have to play with the head unit to get it on or try a 55.
  18. S

    Diff Fluid

    i put in 2 quarts think i should add more?
  19. S

    Diff Fluid

    Just change my diff fluid in my car how much am i suppose to put in?
  20. S

    Supercharger Belt Broke

    Hey guys my supercharger belt broke and i need a new one vortech wants like $60 or $70 for a new one. I tried the local part stores but no one has it. I tried pep boys, auto zone, robbins, advanced, VIP, and napa. They had a 54.25inch belt tried it and i wont fit over the blower pulley. Any one...
Top Bottom
Back
Forums
Menu